"roof screeds"

Ronafix Pre-packed Screed 6-50mm was specified to be laid to falls to provide drainage to the new terrace construction, which provides access to student accommodation and waterproofing to the rear of the shop units below. Early application of the asphalt waterproofing was possible because Ronafix Pre-packed Screed 6-50mm dries faster than traditional sand and cement screeds, reducing the delay between application of the screed and waterproofing.

Smet Supported Partner, Fast Floor Screed pump applied SMET LiteFlo® Lightweight Flowing Screed for the retrofit of this large house in Dalkey Co Dublin. This lightweight screed is ideal for renovation projects where loading is an issue. LiteFlo® is a high-quality, innovative, pumpable factory produced, CE marked, self-levelling screed based on calcium sulphate.German-made LiteFlo® is unique, in that it’s the first pumpable lightweight flowing screed. Made from specially selected aggregates, makes it 30% lighter than conventional flowing screeds and therefore 70% lighter than traditional sand & cement – ultimately this means less is required per m2. Another plus is that screed made from Calcium Sulphate has naturally substantially lower embodied carbon emissions than a sand and cement screed.LiteFlo® complies with EN 13813: 2002, is CE-marked, and is available in 27Kg bags or bulk silos.Have a look at the Northern Builder MagazineTop 5 Liquid Screeds Article.  Read about SMET LiteFlo® in the Irish Construction News.Smet Building Products Ltd in partnership with Fast Floor Screed Ltd, demonstrates, once again, a superior level of customer service, both pre and after-care. Whether your job is self-build, retro-fit, floor renovation, design, commercial, or an industrial venture – the flooring gurus have a floor compound suitable for you.Contact Smet Building Products Ltd 

Demanding environments require a proven system. This 1800m2 Accident and Emergency department was  refurbished with cost-effective, fast track products from ARDEX, to the total satisfaction of the client.

Considered an inspiration to science and culture, the architect's vision of absolute homogeny and clarity was realised with PanDOMO® offering the clean, virtually seamless surfaces required, whilst meeting the demands of high traffic areas.

1,400m² of PanDOMO® Floor, and 700m² PanDOMO® Wall provided the luxurious seamless finish required by Delugan Meissl Architects. At its opening in 2012, the orchestra pit was the largest of its kind globally and is reputed to provide some of the best acoustics in Europe.

Lush sees PanDOMO® as the perfect option for feature walls in their retail locations. It offers rapid installation and provides a unique finish that can be colour matched to their different concepts.

400m2 of ARDITEX NA provided the perfect levelling and smoothing solution for one of the most treasured and distinctive buildings in the UK.

As part of a £50million group investment, the prestigious Colchester club needed 3,500m2 of tiling to cover the swimming pools, changing rooms, walkways and reception areas. Products used: ARDEX A 38, ARDEX E 100, ARDEX S 7, ARDEX WPC, ARDEX X 77, ARDEX X 78, ARDEX X 7, ARDEX-FLEX FS, ARDEX-FLEX FL, ARDEX WA

Australia’s busiest cultural precinct relied on 12,000m2 of ARDEX waterproofing products to offer protection against the enduring threat of moisture.

PANDOMO provided the unique subtle character of polished concrete combined with a seamless, hard wearing floor finish. Products used: ARDEX A 38, PANDOMO® Floor, ARDEX R 3 E, ARDEX EP 2000, ARDEX P4, ARDEX K 80

8,000m2 of limestone tiling was fixed using ARDEX X 7001 W Tile Adhesive with Rapidry Formula  Technology. The luxury tiles were grouted in just two hours, providing the perfect finish to the £675m modernisation of the shopping centre.

Requiring a minimalist look for multiple stores across the globe, ADIDAS specified ARDEX K 80 Industrial Topping/Wearing Surface to provide the look and performance needed for such demanding environments.

Totally refurbished in only 8 weeks after the late realisation that the entire pool floor had to be removed and retiled, ARDEX dived in to offer a fast track solution for theupcoming Commonwealth Games.

Thousands of original English Heritage wooden blocks had to be removed, resurfaced and re-laid using a complete system of ARDEX Fast Track products under the strictest guidelines.

Over 200 million visitors visit Selfridges every year. So when the iconic food hall needed renovating, only ARDEX products could achieve the speed and reliability needed for this high footfall environment which had to be ready for the public every morning.

“ARDEX have developed a range of tile fixing products that exceed expectations, and enabled us to maintain our reputation for excellence. We were delighted with the results at The Savoy”. Rafi Mimoni, MD Mega Marble

As part of Soundis’ ongoing work supplying high-quality acoustic flooring at various Premier Inn’s around the UK, we were brought on to provide acoustic flooring to their Penrith site, one of Premier Inn’s many new sites across the UK.Due to it’s service and close proximity to the Lake District, this hotel has become extremely popular in just a short period of time.Just like a number of our other Premier Inn projects, we supplied an acoustic flooring system to the 1st and 2nd floors. This superb system provides excellent levels of soundproofing while being used in a shallow floor build up.We also supplied XPS Insulation on the ground floor with a 22mm T&G chipboard overlay, maximising durability for the increased footfall.The system we supplied reduced the overall noise within the hotel, allowing Premier Inn to fulfill it’s promise of a good night’s sleep. This installation carried out by UK Acoustic Systems proved to be a great success, reducing the noise levels within the building and helped ensure the most comfortable stay possible for guests.

Alumasc Rooflights provided an ideal solution to allowing natural daylight into the building from above. The unique kerb design incorporates both security and waterproofing to create a reliable, safe and secure rooflight, allowing horizontal termination of the waterproof membrane. This makes water penetration virtually impossible. The domed glazing is moulded from Marlon FSX Longlife, premium quality solid polycarbonate, which has an impact resistance up to 200 times that of glass.Technically sophisticated, Harmer AV high-performance aluminium roof outlets are chosen for this project as they guarantee a trouble-free performance and are especially suited to flat roofing applications featuring continuous membranes.Harmer AV roof outlets combine innovative product design with full industry compliance to meet the needs of rainwater drainage in any construction project, with the ability to drain up to 40% more roof area than conventional gravity outlets. Further to this, their lightweight, durable, non-corrodible design means that they will do so for up to 40 years.GX Pressed Aluminium Gutters are robust box section gutters designed for traditional wet jointing on site. They’re especially suited to applications where maximum capacity gutters are required. For the very large drainage area of the campus roof, they were perfect.Designed to fully accommodate thermal movement at every joint, they are lightweight, durable and noncorrodible, and, upholding the environmental prerequisites of this project, they are 100% recyclable.Finally, Heritage Circular Pipes are available in 4 pipe diameters and 3 pipe lengths, together with a complete range of fittings. Can be factory finished to replicate cast iron or with BBA certificated powder coatings in a range of colours.

In January, Gypsol HTC screed was installed to the ground floors of a new self-build home in North Lincolnshire, UK.The four bedroom, self-build, detached home saw 160 square metres of Gypsol Anhydrite Screed installed by Z K Flow Screed. The floor screed was designed to be placed over underfloor heating, with a depth ranging from 40 – 70mm. It was produced by Ever Readymix in Sandtoft and the pour completed in one day.

Natural daylight can be hard to obtain in some rooms, especially when that room is situated on a second floor. Rooflights and Roof Windows can be a fantastic solution to this. Glazing Vision proved incredibly important to this new build using their technical knowledge and detail to create a new bespoke product to suit the client’s requirements.

Fully compatible products from the range of TBA FIREFLY™ have been chosen to compartmentalise roof voids between apartments and communal lobbies of a large apartment building in the London Borough of Lewisham, providing 120 minutes fire integrity protection as part of a wide ranging refurbishment programme carried out earlier this year.The contract on Lewisham Homes’ Commodore Court in Albyn Road has been led by the sector specialist construction company, Mulalley & Co. with London/Sevenoaks based CLM Fireproofing carrying out the installation of the TITAN Lite™ 120:60 barrier system, in combination with Collaroll and the use of ancillary products from the FIREFLY™ range.CLM Fireproofing was founded 30 years ago by Clive Miles and has established a reputation as a leader in the fields of both passive fire protection and fire-stopping; working in a variety of sectors on projects right across the UK. A regular user of the FIREFLY™ range, many of its operatives have attended courses at the company’s premises in Rochdale to become trained FIREFLY™ installers.The Site Agent for CLM, Virginijus Pasvenskas, commented: “There was initially an intention to use a mineral wool flexible fire barrier, but the product was not tested for the scenario installed around the services such as a downpipe and it was upgraded to the use of the FIREFLY™ system by the client/project team. The installation of the TITAN Lite™ and the Collaroll to wrap the trusses and the services went very well and, as well as supplying specific details for the work, FIREFLY's technical team came to site to inspect the works. We completed our contract on schedule back in the summer.”TITAN Lite™ 120:60 has been developed for use in vertical separation or compartmentation situations, offering 120 minutes integrity and 60 minutes insulation and is able to be sealed around penetrations. It is widely specified to form fire barriers within roof voids and floor voids in many different property types, including tower blocks and other HMOs.The flexible woven material is easy to cut and fix, and is chemically treated to improve its cooling properties and therefore prevent temperatures rising in adjoining areas. The system has been fully tested to BS 476 Parts 20 & 22 and is third party certified by IFC. The six metre long rolls of TITAN Lite™ 120:60 have a minimum thickness of 6mm and are installed using special staples as well as high temperature adhesive.Employed as part of the FIREFLY™ System and also to wrap the services which penetrate barriers such as PHOENIX, ZEUS Lite™ and APOLLO Lite™, Collaroll comes in a roll which unwraps to 10m long x 300mm wide with a sewn in concertinaed skirt. The skirt can be moulded to shape to seal it neatly to the upright barrier, which is usually at 90 degrees to the Collaroll and fixed into place using the FIREFLY™ high temperature adhesive. The R31 Staple Gun and Staples are used to staple the Collaroll to itself tightly around the penetration.

Ronacrete was called to a site meeting at The Brunswick Centre in February 2017 to discuss detailing of Ronafix floating screeds laid to falls where the required balustrade heights on the podium decks restricted the minimum screed thickness. It was agreed that a minimum screed thickness of 35mm could be applied if plant and materials were only positioned on thicker sections of screed until after granite paving had been laid, to ensure that heavy point loads did not cause deformation of the insulation boards.

👉 Client: Rathcorbally Construction👉 Insulation: baseTherm® 200👉 Floor Screed: Sudanit 280 Alpha Hemihydrate Floor Screed over UFH👉 Floor area: 880 m2baseTherm® is:👉 Seamless & void free👉 Without heat loss or cold bridges👉 Full encapsulation of services👉 No surplus & no waste👉 Levels the substrate = even thickness of screed👉 Even screed thickness = uniform heat

For the new distribution centre at Schiphol Trade Park along the A4, living walls have been realised with MobiPanel, the living wall system from Mobilane. With a total surface spanning 750 m2, the facades of the new distribution centre is greened with the latest generation vertical green from Mobilane.Sustainable and innovative distribution centreA lot of attention has been paid to the appearance of the new distribution centre. With the design of Dedato Architecten, sustainability has not only been taken into account on the inside, but also sustainability at the outside of the building has been taken into consideration by including nature-inclusitivity. Dick Venneman, architect and owner of Dedato Architecten tells: “It is a building with its own characteristic appearance, a landmark from the highway. The building is in its materials friendly and accessible. The different surfaces in the facade gives it a human approach. The living walls and the vertically placed solar panels tells something about the sustainability of the building and plays a role in the preservation of biodiversity in the area”. In addition, the MobiPanel living walls makes the environment more sustainable and improves air quality. The installation of the living walls was carried out by Mobicare in collaboration with Zoontjens Boomprojecten. In addition to the living walls, Zoontjens also installed two large roof gardens with various trees, shrubs and 2,600 MobiRoof ECO sedum cassettes totalling 650 square metres.Distribution centre 2.0 Schiphol Trade ParkThe building spans 30.000 m2 of which 3000 m2 is available for offices. Under the distribution centre, there is a car park spanning 7500 m2 with space for 270 cars. The construction of the new distribution centre began in 2020 and is delivered by Dijkham Bouw BV. “From the environment, wellbeing and to prevent a paved environment, for the design it has been chosen to implement living walls, green roofs and ground level. We are very satisfied about this procedure. The execution is very good, the communication was good”, according to Marcel Smeets – Coordinator at Dijkham Bouw BV. The distribution centre was developed by Minerva Development. Minerva Development is an independent developer with years of experience in the development and realisation of business premises. “Since Schiphol Trade Park has set the goal of becoming one the most sustainable logistics centre, as developers we were very happy to take on the challenge. Next to all other facilities such as solar panels, we have opted for a lot of greenery in the design. Not only on the facades, but also in the surroundings of the building and on the roof. We are very happy with the end result and proud of the fact that because of the living walls, this is by far the most beautiful DC in the area. We are very curious about what the result will be over a few months when everything is in bloom”, Bob Lukassen – Minerva Development.Latest generation vertical greenFor greening the distribution, it was chosen for the new living wall system MobiPanel from Mobilane. MobiPanel is an innovative, sustainable and lightweight system for living walls. It is a modular and circular system consisting of omega profiles and pregrown plant cassettes (40 x 40 cm), provided with an automatic irrigation and drainage system. The plants in the cassettes receive water through capillary action. MobiPanel can be installed on flat or curved walls and is suitable for different types of walls, including certain types of sandwich panels. For the facades of the new distribution centre, sandwich panels from Cladding Point have been used. “With Mobilane, as a global expert with many years of experience, we can continue to lead the way in innovation and sustainability. Cladding Point and Mobilane are ready for the future together”, Frank Janssen – Managing Director at Cladding Point. Cladding Point’s Design+ Carrier sandwich panels contribute to the highest BREEAM category.Client: Minerva DevelopmentArchitect: Dedato ArchitectenConstruction period: 2021Installation: Mobicare

Job: Maldron Hotel Swimming Pool Renovation, Portlaoise, Co. Laois.Smet Supported Partner:Precision Building Services – Mark PembertonProducts: Sopro Rapidur® B5 Rapid Drying Screed BinderMerlin Barrier CoatSopro RAM 3 (454) Renovation and Levelling MortarSopro GD 749 Universal Floor and Wall PrimerSopro DSF® 523 Tanking MembraneSopro PUK 503 PU AdhesiveSopro VF HF 420 – VarioFlex® High Strength Flexible Tile AdhesiveSopro’s No. 1 Flexible Tile AdhesiveSopro FKM® XL 444 – Extra Light Weight Tile AdhesiveSopro Sanitary SiliconeSopro DE 014/015 Sealing CornersSopro FEP 508Sopro DBF-638Racofix 818Description:SMET supplied Smet Supported Partner, Precision Building Services (Mark Pemberton), for the renovation of the Maldron Hotel Swimming Pool, Portlaoise, Co. Laois. A total area of Floor screed @ 140m² | Wall tiling @125m² | Floor tiling @ 140 m² was completed.New floor installation with fast-track – rapid drying floor screed solution, using Sopro Rapidur® B5 Rapid Drying Screed Binder, a fast-setting screed which was laid to falls prior to waterproofing and tiling providing an early completion. German-made Rapidur® B5 Rapid Drying Screed Binder is a special polymer-modified binder for particularly economical ­production of high-strength, rapid-set cement screed – based on DIN 18560.Rapidur® B5 is suitable for use on heated screeds, bonded screeds, unbonded screeds and floating screeds. This flooring solution is particularly useful for fast-track or tightly scheduled screed laying. The newly laid Rapidur® B5 screed floor is ready to receive floor covering after approx. 3 days – after achievement of moisture content ≤ 1.8 % CM. Sopro Rapidur® B5 is supplied in 25kg bags, with 40 bags per pallet.Sopro Rapidur® B5 was installed directly on top of Merlin Barrier Coat wet on wet. The screed was ready for waterproofing/tiling after 3 days. This system was also used to repair the Jacuzzi’s surrounding walls prior to waterproofing, tiling, and grouting.Sopro RAM 3 levelled the deck area (3-60mm) between the drainage channel edge and pool perimeter movement joint. Sopro RAM 3 was bonded with Sopro GD 749.

Our premium granite TerraPave® flagstones were a perfect choice for this scheme at one of London’s foremost rooftop cocktail bars and pizzerias. Skylark Roof Garden, located on Kingdom Street, sits on the 10th floor of Paddington Central, offering incredible views overlooking the beautiful Notting Hill, on the banks of Little Venice. For this project, a combination of Pedestals and TerraPave® flags were utilised. The incorporation of Pedestals (stools on which the flags were laid) , meant no base was required. The depth of TerraPave® flags is calibrated as part of the manufacturing process, delivering exceptional dimensional accuracy which in turn delivered consistent levelling across the terrace. Project architects, Allies and Morrison selected our TerraPave® Flags, in Rimini and Milano Ground due to their rich, distinctive styles and impressive durability in highly pedestrianised areas. These flags are produced with locally-sourced, natural aggregates instead of pigments meaning their unique colouration won’t fade. TerraPave® also offers a cost-effective, and practical alternative to traditional stone paving. The £80m Paddington Central scheme was completed built by Wates Construction and designed by Allies & Morrison. Some of the impressive project’s additional features include London’s highest basketball court, an external glazed stair tower, and a public colonnade around the retail space on the ground floor.

Refurbishment of an old mill, using electrical underfloor heating. 50mm Gyvlon screed incorporating the electrical underfloor heating. The Gyvlon screed was easily pumped into the upper and subsequent floors speeding up installation compared to sand cement screeds. The design also maximized the effectiveness of the underfloor heating, whilst complying with Part E of the Build regulations.

This impressive listed building retains its character with Glendyne natural slates on all visible slopes.

Product: Elasto-KoteProject: Commercial Units, GlasgowProject size: 1400m²Location: Glasgow

Project: FedEx Transfer StationProduct: Elasto-Kote (Portland Grey)Project size: 25,000m²Completed in: 2 WEEKSApplication: Spray appliedGuarantee: 20 years

A major development has seen the creation of some 300 contemporary new homes in the heart of a country park in Kent. The Conningbrook Lakes scheme was built by the Chartway group, a leading Kent based developer, with GDM Architects responsible for the main design. RCM were asked to supply their Supertech Weatherboard for the exterior of the different types of houses, ensuring an individual finish for the different house types.

Product: FastCoat ProProject: Carlisle Race CourseProject size: 600m²Location: Carlisle

During the early 19th Century, a large section of the South Bank of the River Thames, London, comprised small wharves, docks and other industrial uses. In more recent years, the site has been used as a delivery depot, however, it is only now that the value of the site has been realised as a prime mixed-use location.

The Highland was specified for a 212 plot site by Redrow Homes in the South West of England.

As Royal Warrant Holder, Penny Hydraulics are responsible for the installation and maintenance of all Royal Household chandelier raising and lowering systems across London. Designed to provide fast and safe access to suspended luminaires for cleaning and maintenance, chandelier winch systems are widely used throughout Royal properties.

Overlooking the majestic panorama of the Dolomites, the hotel was completely rebuilt with the aid of ARDEX products. Inclusive of 6 indoor and outdoor swimming pools.