NBS Source
List your products

Naylor Concrete Products Ltd

+44 (0)1226 320810 www.naylor.co.uk

Sort by:

Showing 1-36 of 62

Economy Lintels

A cost effective, fully reversible unit for use in standard housing or a small load situation. All Economy lintels are suitable for use with L-Strip. An ex-steel mould finish and made from wet cast concrete. May see small air holes on the surface, aggregate and concrete fines to bottom arrises. For use normally in plastered situations. For exposed situations see Fair Faced range.

Standards:

  • Design complies with BS 8110-1 Section 4.
  • Manufactured in accordance with BS EN 845-2.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.

Faced Fire R11 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire R13 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire R14 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire R190 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire R2 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire R3 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire R7 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire R8 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire S5 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced Fire S8 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R11 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R12 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R13 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R14 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R190 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R2 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R3 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R6 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R7 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R8 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced R9 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced S4 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced S5 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Faced S8 - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R11 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R13 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R14 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R190 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R2 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R3 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R7 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire R8 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire S5 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Fire S8 [60 minutes] - Lintels

Fire-Spec is a range of ex-steel mould finish high performance units, available in 60, 90 and 120 minutes, dependent upon the section width. Other concrete sections can be made with a fire resistance equal to or greater than our standard range and our technical team with their special knowledge of concrete can advise you on which sections would achieve a specific fire resistance and strength rating and offer a design solution should this not be detailed in our load span tables.

Fair Faced Fire-Spec range:

Fair Faced Fire-Spec lintels are also available in a class C fair faced finish and again with a 60, 90 and 120 minute fire rating.

Standards:

  • Design complies with BS 8110 table 4.3, section 2.
  • Manufactured in accordance with BS EN 845-2: 2003.
  • Materials comply with BS EN 206 and BS 8500. The pre-stressing wire complies with BS 5896.
  • All fire rated lintels produced by Naylor Lintels comply with BS 8110 table 4.3, section 2.

Showing 1-36 of 62