"steel reinforcement for concrete"

Shooters Sports bar is a modern sports bar located in Neath Town Centre, a principal area of Port Talbot, Wales.  A popular venue, well known for its 6 screens showing live sports, licensed bar and pool, American pool and snooker tables.Delta Registered Installers, Tywi Damp Proofing were first approached to offer remedial assistance with a section of wall which was experiencing severe water ingress.The structure being of reinforced concrete and old wall construction was allowing water ingress via cracks in the structure.Most faults in older structures which allow water ingress are either damaged or deteriorating mortars.Any cracks in the brickwork or substrates will also allow water to enter a structure and would need addressing in creating a Grade 3, habitable space under BS8102:2009 “Code of practice for protection of below ground structures against water from the ground”.Prior to proposing remedial works, ground water assessment, drainage and associated risk assessments were all undertaken.

A hugely popular handrail design that ASF have supplied to projects in many locations. The full sized bollards that are used as post uprights give a sense of solidity and permanence, whilst the mitred top gives them just enough of a decorative nature to lift the product beyond a simple post and handrail job. In this project all welds and interfaces were polished back on site so the finished product becomes a complete unit with no visible fixings. With both double and single handrails over multiple flights and angles, this project shows how ASF can manage any project need.

Smet Supported Partner, Adston Construction, machine applied the LIDL External Render System onto Poroton blocks consisting of a Base Coat of Bauprotec 850 M – Lightweight Lime Cement Render, Façade System Primer and a Finish Coat of Mineral Finish Coat. The Plinth Render used is Bauprotec SLP – Lightweight Plinth and Tanking Render. Key Coat: Change of substrate concrete/steel pillar/Poroton block or mass concrete: Bauprotec RHS was used.The Internal Render System specification onto Poroton blockwork consists of Single Coat: Bauprotec 850 M, Lightweight Lime Cement Render. A smooth finish is required in the sales area, so either 850M steel trowelled smooth or skim finished. Key Coat: Change of substrate concrete/steel pillar/Poroton block: Bauprotec RHS used.The LIDL render system, available from SMET:Bauprotec 850 M is a factory-produced Lightweight Lime Cement Render, specially designed for machine or hand application produced to EN 998-1: 2010 and is CE Marked.Bauprotec RHS is a CE Marked, factory-produced highly polymer-modified render specially designed for hand and machine application produced to EN 998-1: 2010.Mineral Finish Coat – K is a CE marked, factory-produced, mineral-based, high-quality finish-coat render, specially designed for hand and machine application to EN 998-1, 2010.CASEA Bauprotec SLP is a CE Marked, factory-produced Lightweight Sand & Cement Render specially designed for hand and machine application produced to EN 998-1: 2010.The special render properties; lightweight, low thermal conductivity, high yield, and Smet Supported Partner superior technical backup, are key factors in choosing SMET. SMET is committed to delivering consistently superior quality, German-made Render Systems to Lidl Plastering and rendering/plastering Contractors across the UK and ROI. If you need to speak to us - click to contact SMET.All LIDL spec SMET Render System products are available from Smet Building Products Ltd, which ensures the contractor has a superior level of technical backup in the machine application of the LIDL specification.

Project at DB Schenker to create temperature controlled enclosure in new warehouse using reinforced fabric partition wall

Delta were employed to assist on this leaking podium deck project. Following a full assessment of The Hub and its underground parking facilities it was identified that rainwater was entering the basement car park through the ceiling deck at multiple points. These points included holes that were formed to allow drainage from the surface, movement joints and investigation holes that had been created through the steel rib and concrete deck. Based on “as built plans” a system was designed post construction that would offer the same quality of structural protection had it been incorporated during the build phase.

We are able to manufacture engineered wood stair units to match our flooring with the same colour and finish.The stair units include the tread and riser and can be made to exact sizes if we have detailed drawings. This means installation costs will be less. These stair cladding units can be fully bonded to old stairs, concrete stairs or Steel stair structures.The cost of these stair units are considerably more than our standard stair nosings and a deposit will be required before production because they will be to your specification. Lead times are around 12 weeks.

Located in Tower Hamlets, Gayton House and Sleaford House are managed by housing association Poplar HARCA. Following amendments to Building Regulations, which banned the use of combustible materials in external walls of high-rise buildings above 18m, StoTherm Mineral K was specified to replace the existing EWI system.BBA-certified, StoTherm Mineral K comprises mineral fibre insulation boards and the system is classified with an A2-s1, d0 reaction to fire in accordance with BS EN 13501-1.Working on behalf of Westminster Building Company, Square 1 Architectural Solutions was responsible for removing the existing EWI and installing the StoTherm Mineral K system onto four elevations on each 23-storey block. The non-combustible mineral fibre insulation boards were secured to the existing concrete substrate using adhesive and mechanical fixings, and without the need for additional expansion joints.A StoLevell Duo Plus reinforcing coat embedded with Sto-Glass Fibre Mesh was then applied to the face of the insulation boards. This was followed by the application of 1.5mm stippled StoSilco, a silicone resin render that provides high levels of water repellence to protect the walls from weathering.

DescriptionLocal Smet Supported Partner, a seasoned Lidl Contractor, McCallion Group machine applied the LIDL External Render System onto Poroton blocks externally using as Base Coat: Bauprotec 850 M – Lightweight Lime Cement Render, and as Key Coat: Change of substrate concrete/steel pillar/Poroton block or mass concrete and insulated plinths: Bauprotec RHS Multi-Purpose Render.The internal Render System specification onto Poroton blockwork consists of a base of Coat: Bauprotec 850 M, Lightweight Lime Cement Render, sponge floated in warehouse areas, and skim finished in sales areas. Key Coat: Change of substrate concrete/steel pillar/Poroton block: Bauprotec RHS is used.The Irish LIDL render spec, available from SMET consists of:Bauprotec 850 M is a factory-produced Lightweight Lime Cement Render, specially designed for machine or hand application produced to EN 998-1: 2010 and is CE Marked.Bauprotec RHS is a CE Marked, factory-produced highly polymer-modified render specially designed for hand and machine application produced to EN 998-1: 2010.The special render properties; lightweight, low thermal conductivity, high yield, and the Smet Supported Partner superior technical backup, are key factors in choosing SMET.SMET is committed to delivering consistently superior quality, German-made Render Systems to Lidl Plastering and rendering/plastering contractors across the UK and ROI.  If you’d like to speak to us about your Lidl job – contact SMET.All LIDL spec SMET Render System products are available directly from Smet Building Products Ltd, which ensures the contractor has a superior level of technical backup in the machine application of the LIDL specification.Related DownloadsTDS CASEA Bauprotec 850 M – Lightweight Lime Cement RenderTDS CASEA Bauprotec RHS – Multi-Purpose Render

Falco has completed the fourth cycle hub installation at The Telford Langley School in Telford as part of a new tranche of secure cycle hubs located at key areas across the borough.The scheme which got underway last year involves the design, manufacture, supply and installation of bespoke cycle hubs coupled with associated FalcoLevel-Eco two-tier cycle racks to allow commuters, residents and visitors to quickly and conveniently park their bike whilst on the go.The latest 6m x 4m cycle hub as shown here at The Telford Langley School, is based upon the UK’s most popular cycle hub design – the FalcoHub, which is manufactured from a combination of a hot-dip galvanised steel frame with reinforced safety glass cladding. FalcoLevel-Eco two-tier cycle racks have been installed providing secure accommodation for up to 28 bikes.A convenient FalcoFix 2.0 cycle station has been supplied allowing cyclists to inflate tyres and carry out basic cycle maintenance whilst on the go.The secure cycle hub also comes complete with proximity LED lighting, eye-catching ‘Travel Telford’ branding graphics and powder coating in an Anthracite Grey RAL colour.In addition to the cycle hub here at The Telford Langely School, Falco has also manufactured and installed three other cycle hubs for Telford & Wreking Council, with other cycle hubs located at Rampart Way – across the bridge from Telford Central Station, at Wellington Civic & Leisure Centre – to the right of the car park entrance, next to the Wellington Town Council building and at Oakengates Station – situated to the right side of the main entrance.The FalcoHub, as shown here for Telford & Wreking Council, is a contemporary cycle store manufactured from a combination of a galvanised steel frame and reinforced safety glass, designed to be sympathetic to the surrounding area. The FalcoHub was developed by Falco’s in house design team to ensure it met the client’s specification including structural calculations so that the whole design meets the UK/European CPR regulations EN1090 and is CE marked.For more information about the scheme here for Telford & Wrekin Council or how Falco can assist your cycle parking scheme, please contact our helpful sales team on 01538 380080.

AEM Demolition undertook the heavy side building works of the 35,000 square feet M&M World in London. AEM required an access solution to provide reliable, durable and easy access to the building’s underfloor services. Howe Green’s 5000 Series Stainless Steel access covers were selected. The covers were installed in a range of different internal areas as well as with a wide variety of different types of flooring, including bright red resin, painted concrete and carpet. Designed and built to withstand the pressures of high volume pedestrian traffic, the covers have a 1 hour fire rating.

Metrotile has often stated that their Lightweight Steel Roofing systems can go head to head with ‘traditional’ materials aesthetically, and Gorse Hill School is a fine example of this statement in action.Gorse Hill is unique as it required a partial refurbishment. Some, but not all of the blocks roofs where in urgent need of repair. For these roofs, Metrotile’s classic ‘Roman’ profile was specificied as its contoured design matched the concrete Roman tiles that remained on some of the buildings.The finished product, is a fine example of old meeting new with brilliant results. Another important factor involved with the specification of Metrotile was the need for a secure roofing solution.

Solid wood floor specialist Junckers worked closely with world-renowned architects BIG (Bjarne Ingles Group), to create a custom finished oak floor for the M/S Maritime Museum in Helsingør, Denmark. The textured floor acts a link within the interior scheme of the award winning building, bringing together elements of concrete, glass and steel, housed in an amazing 150 metre long, old concrete dock. The architects’ brief was for a solid hardwood floor that can withstand the heavy footfall of a national museum, with a rustic quality to soften the raw and patinated concrete and large glass panels featured throughout the building. Junckers created a textured finish solid oak floor, which gives contrasting warmth to the overall impression of the museum. By using a specially developed hard brushing technique, the outer sapwood layer of the timber is removed, leaving a tactile, textured surface to expose the beautiful grain patterns naturally inherent in oak. The floor is finished in Junckers Ultra Matt Lacquer resulting in a matt, very hard-wearing floor. The lively two-strip oak floors really come into their own in the large, open spaces of the museums galleries. When natural light from the floor to ceiling glass wall hits the surface of the floor at an angle, it creates a spectacular effect. Following the immense success of the project, Junckers has added the incredible textured finish to many of its floors, both two-strip and wide board planks.

Service stations are notorious areas for high intensity traffic, where vehicles brake and accelerate, and where there is also a high concentration of hydrocarbons on the ground: petrol, diesel, lubricating oils.This is the main reason why CNG Fuels Ltd. has specified ULMA Civil F400K and F300K models in Fuel Stations across the country.CNG Fuels already supply 2,000 vehicles a day from its five public access refuelling stations, and a sixth station at Knowsley, near Liverpool, where ULMA drainage channels have being installed. This station, close to the M6 at Erdington, east of Birmingham, can refuel up to 500 HGVs a day.We have also supplied our F300 and F400 channels to Bellshill, Knowsley, Newark and Avonmouth stations.Civil F heavy duty drainage channels

Floor Painters Limited, have used UltraFloor to complete a 2,100 sqm industrial flooring project at a historic steel forge.Experienced industrial flooring experts, Floor Painters Limited, have used a number of UltraFloor materials to complete a 2,100 sqm industrial flooring project at a historic steel forge in Lincoln.BackgroundBuilt over 100 years ago, the existing floors in the steel forge were damaged and unsafe. After careful consideration, it became clear that replacing the original concrete floor was not a practical option in terms of time and cost.The ChallengeThe steel forge remained fully operational throughout the project and so the challenge was to find a range of flooring materials perfectly suited for industrial use and that could be trafficked quickly so as not to disrupt any work being carried out.The SolutionWith decades of expertise, Floor Painters Limited knew UltraFloor materials were key to a successful outcome.After removing the damaged concrete floor, the concrete substrate was sealed using UltraFloor Prime IT Multi-surface Primer. Formulated to promote adhesion to all UltraFloor smoothing underlayments, Prime IT Multi-surface Primer is pigmented pink for excellent coverage control and is proven to reduce pinholing, minimising the risk of costly failures. With a coverage rate of 200sqm at 3:1 dilution, Prime IT Multi-surface Primer is a must-have product for all flooring installation projects.The following day, Level IT Base was applied, via pump, at an average depth of 50mm. Level IT Base is a heavy duty, deep fill smoothing underlayment, formulated to build depths of up to 50mm thickness. Level IT Base also boasts a high compressive strength – an important requirement for all industrial flooring applications.Once Level IT Base had cured, Level IT Top was pump applied to an average depth of 10mm and left to cure. Ideal for use with Level IT Base, Level IT Top is a heavy duty, abrasive resistant surface finish, designed for use as a wear surface, and can receive forklift traffic after only 36 hours – the ideal product for warehouses and manufacturing facilities where downtime is not an option!Both Level IT Top and Level IT Base can be pump or trowel applied for ease of application, are moisture tolerant, have a 30-40 minute working time and can receive foot traffic after just 3 hours.To complete the installation, the cured floor was then prepared by industrial grinding before the application of two coats of a solvent free epoxy coating – resulting in a flat, hard-wearing, safe and fit for purpose floor.ResultsThe project was completed in six stages, over 36 days, carrying out between 300 and 500 sqm a day, depending on the work space made available. On completion of the project, Terry Rossington, Director of Floor Painters Limited, commented: “Our client was very happy with the standard of the finish and the upgrades made to their working environment, which has improved both visual appearance and functionality of the floor.”

This mixed use development on the southern fringes of the Olympic Park utilised the Nexus® system to achieve flawless brick-faced soffits to the hundreds of door and window heads. Nexus is a two-part brick soffit system that combine a high integrity stainless steel brickwork support system with custom-designed prefabricated brick faced soffit units. Being 70% lighter than traditional cast concrete solutions, the Nexus soffit system is simply lifted and bolted into position by hand and, as the brick slip facing is manufactured from the same batch as the main brickwork, presents a perfect colour and texture match for flawless transitions.

The Cambridge University Faculty of History required a solution to level the existing flat roofs of the historical Stirling Building. The aim was to create a vibrant and attractive area, mainly used as a throughway, it was paramount that the tiles would match the existing colour of the surrounding building.Our Castlepave GRC Promenade slab (450x450x38mm) was selected, and a custom-made colour was created to blend effectively into the existing architecture. We manufactured various test batches each with a different shade of red, and hand finished aged effect. Once the colour was selected from the various test batches, they were manufactured by hand to the customers specification and delivered to site.We assessed the fall and height tolerances of the roof to determine the number and size of pedestals required to provide a completely level finish. Adjustable Pedestals ranging from 30-120mm,10mm fixed height stackable pedestals, levelling shims, and self-levelling heads were used.The outer row of slabs was cut to size on site, using a circular saw. As shown the results are a flush finish that minimizes the gaps between the slabs and the exterior perimeter. The glass reinforced concrete composition of the slabs mean they are strong and easy to work with on site.The Client was very happy with this stylish and unique finish.

KEIM Concretal W was applied to the external concrete to give a vibrant white finish with unparalleled concrete protection which will not fade and yellow over time. KEIM Concretal W provides an integral protective and decorative finish to the concrete.

DescriptionLocal Smet Supported Partner, master builders NRS Group Construction, machine-applied the LIDL External Render System onto Poroton blocks externally using as Base Coat: Bauprotec 850 M – Lightweight Lime Cement Render, and as Key Coat: Change of substrate concrete/steel pillar/Poroton block or mass concrete and insulated plinths: Bauprotec RHS Multi-Purpose Render.The internal Render System specification onto Poroton blockwork consists of a base of Coat: Bauprotec 850 M, Lightweight Lime Cement Render, sponge floated in warehouse areas, and skim finished in sales areas. Key Coat: Change of substrate concrete/steel pillar/Poroton block: Bauprotec RHS is used.The Irish LIDL render spec, available from SMET consists of:Bauprotec 850 M is a factory-produced Lightweight Lime Cement Render, specially designed for machine or hand application produced to EN 998-1: 2010 and is CE Marked.Bauprotec RHS is a CE Marked, factory-produced highly polymer-modified render specially designed for hand and machine application produced to EN 998-1: 2010.The special render properties; lightweight, low thermal conductivity, high yield, and the Smet Supported Partner’s superior technical backup, are key factors in choosing SMET. SMET is committed to delivering consistently superior quality, German-made Render Systems to Lidl Plastering and rendering/plastering contractors across the UK and ROI.  If you’d like to speak to us about your Lidl job – contact SMET.All LIDL spec SMET Render System products are available directly from Smet Building Products Ltd, who ensures the contractor has a superior level of technical backup in the machine application of the LIDL specification.SMET is committed to delivering consistently superior quality, German-made Render Systems to Lidl Plastering and rendering/plastering contractors across the UK and ROI.  If you’d like to speak to us about your Lidl job – contact SMET.

The Key Theatre in Peterborough’s city centre combined Bauder’s reinforced bitumen membrane waterproofing system and sedum blanket green roof finish with a photovoltaic solution, which the council’s contract manager.

Falco has completed the fifth cycle hub installation at Telford Town Park Visitor Centre as part of a new tranche of secure cycle hubs located at key areas across the borough.The scheme which got underway last year involves the design, manufacture, supply and installation of bespoke cycle hubs coupled with associated FalcoLevel-Eco two-tier cycle racks to allow commuters, residents and visitors to quickly and conveniently park their bike whilst on the go.The latest 4m x 4m cycle hub as shown here at Telford Town Park Visitor Centre, is based upon the UK’s most popular cycle hub design – the FalcoHub, which is manufactured from a combination of a hot-dip galvanised steel frame with reinforced safety glass cladding.FalcoLevel-Eco two-tier cycle racks have been installed providing secure accommodation for up to 18 bikes.A convenient FalcoFix 2.0 cycle station has been supplied allowing cyclists to inflate tyres and carry out basic cycle maintenance whilst on the go.The secure cycle hub also comes complete with proximity LED lighting, eye-catching ‘Travel Telford’ branding graphics and powder coating in an Anthracite Grey RAL colour.In addition to the cycle hub here at Telford Town Park Visitor Centre, Falco has also manufactured and installed four other cycle hubs for Telford & Wrekin Council, with other cycle hubs located at The Telford Langely School, Rampart Way – across the bridge from Telford Central Station, at Wellington Civic & Leisure Centre – to the right of the car park entrance, next to the Wellington Town Council building and at Oakengates Station – situated to the right side of the main entrance.The FalcoHub, as shown here for Telford & Wrekin Council, is a contemporary cycle store manufactured from a combination of a galvanised steel frame and reinforced safety glass, designed to be sympathetic to the surrounding area. The FalcoHub was developed by Falco’s in house design team to ensure it met the client’s specification including structural calculations so that the whole design meets the UK/European CPR regulations EN1090 and is CE marked.For more information about the scheme here for Telford & Wrekin Council or how Falco can assist your cycle parking scheme, please contact our helpful sales team on 01538 380080.

Made-to-measure stainless steel worktops, by GEC Anderson, were recently specified by Munkenbeck and Partners at the highly desirable city space known as 55 Gee Street, Clerkenwell.The funky, new build, mixed-use development comprises offices, shops and six, high-end apartments. Four flats have two bedrooms, a two bedroom duplex occupies ground and basement levels whilst the 150 m penthouse has three bedrooms. Previously the site was occupied by a building belonging to Her Majesty’s Stationery Office.Outside, the distinctive street facade resembles a Jenga block game, made up of extruded airbricks, randomly assembled. The bricks allow natural cross ventilation through the wall without having to make the glass panels move.Inside, the contemporary living spaces are high tech and high quality. Concrete, wood, stainless steel and glass dominate the open, elegant and functional spaces. The continuous and expansive stainless steel worksurfaces blend-in perfectly within their neutral and effortless surroundings. Formed in one piece, the GEC Anderson custom stainless steel worktops include integral sink bowls and edge detailing. Full height splashbacks are included to alcove worktops whilst the striking penthouse kitchen includes a stainless steel island element.Stainless steel worktops and splashbacks still are often associated with only commercial kitchens. However, discerning specifiers have always recognised stainless steel as an interesting, practical and versatile worktop material for residential kitchens. GEC Anderson, with its high quality, brushed satin, stainless steel worktops has helped to promote the popularity of stainless steel within this environment, since the early Sixties.Alfred Munkenbeck, Munkenbeck and Partners, chose GEC Anderson worktops because they could be made in one piece, to the exact size and shape required and with the desired edge profiles, sink bowls and details. The highly specific requirements and details are matched by the quality, appearance, design honesty, integrity and practicality demanded by the apartment settings.GEC Anderson stainless steel worktops and splashbacks are made to order in any shape or size, with seamless finish and no visible joins or junctions. The Touch kitchen units, from OIKOS, were supplied by Eurobath Trading UK. A full measuring and installation service was provided by GEC Anderson for main contractor, Morgan Sindall.

Cambridge Central Mosque is Europe's first eco-friendly mosque and the first purpose-built mosque within the city of Cambridge. The mosque is well insulated and naturally ventilated, using efficient heat lights in the roof and solar panels on the top to help generate renewable energy.Cellecta XFLO Micro was specified by Marks Barfield Architects as its underfloor heating insulation boards were used to help create an efficient and environmentally friendly heating system. Cellecta ScreedBoard 20 was also specified for the overlay floorboard. It is suitable for all types of steel, concrete and timber floors.Warmafloor were awarded this 250m² contract to develop this eco-friendly structure.

The remarkable 22 Bishopsgate Project stands as the second tallest building in the United Kingdom and Western Europe, showcasing its architectural prominence. On its 58th floor, an awe-inspiring viewing gallery offers breathtaking vistas. Perched even higher, on level 59, a discreetly hinted restaurant is poised to offer an unparalleled dining experience, with a renowned chef at the helm. Although the details remain a secret, the restaurant promises to be a highlight. Beyond its striking stature and exclusive amenities, the project's core objective revolved around enhancing the base build construction to optimize noise levels for the activities and events within the Viewing Gallery. Aiming to strike a balance, the project sought to both amplify the permissible noise levels for these events while curbing any potential noise breakthrough into adjacent spaces.In the dynamic context of 22 Bishopsgate, where concrete installation was unfeasible due to location and occupied lower floors, a visionary solution was sought. Over 1246m², the innovative Stravifloor Channel floating floor system was meticulously installed. In lieu of concrete, a bespoke approach utilizing high mass calcium sulphate boards was designed, ensuring both functionality and practicality. Addressing concerns about floor height, custom-designed bearings were engineered to maintain top-tier acoustic performance, with a mere 30 mm thickness.Despite a demanding timeline to unveil the viewing gallery, the project remained on track. Stravifloor Channel, with isolated steel battens, played a pivotal role. Galvanized steel channels provided robust support over isolation pads, while the optimized discrete supports allowed minimal contact points to the subfloor.

‘Autobarn’ is an unusual build comprising an elegant five-bay garage and accompanying workshop sitting within the grounds of a Grade-II listed 18th-century home in Somerset.Designed by Bindloss Dawes Architects, the brief was to create a garage with an adjoining workshop to house the client’s classic car collection. The finished result is an aesthetically beautiful building with its deceptively simple wooden barn-themed styling using agricultural materials such as concrete and recycled wood under a zinc roof. With surfaces comprising steel, timber and polished concrete floor, the architects incorporated Troldtekt acoustic panels to clad both the walls and ceilings between the steel frames for sound absorption and to combat the issue of reverberating noise.The added advantage of having services hidden behind the white panelling means the final result is a stunning simplistic and minimalist design allowing the classic cars to be the focus of attention and transforming the space into more of a gallery than a traditional garage.Troldtekt acoustic panels are available in a variety of different surfaces and colours and combine sound absorption with a tactile surface. With an expected life cycle of at least 50 years and resistance to humidity and impact, they are available in various sizes and four grades, from extreme fine to coarse. The panels can be left untreated or painted in almost any RAL colour. Depending on the panel specified, reaction to fire is classed in accordance with EN 13501 as B-s1,d0 or A2-s1,d0 respectively. Founded on the Cradle-to-Cradle design concept and having attained Gold certification, Troldtekt wood wool acoustic panels are manufactured using wood from certified forests (PEFC™ and FSC®C115450) and can contribute positively to a building’s BREEAM, DGNB or LEED points. 

SubFloor flooring was used in a conversion of an industrial premise for youth gaming activities. This allowed insulation to separate the cold floor from the main area and for wiring installations under the floor.This simple and elegant solution raised and levelled the floor to allow for installations and insulation. The joist and screw system allows for quick and easy assembly so that the floor can reach the desired height.95 mm Rigid insulation was positioned on the insulation bearers and a 22 mm chipboard was placed on top.Products:Wooden Joist 45x45x3600 mmSubFloor Screw 200 mmSubFloor Screw FootInsulation Bearer 95 mmHeight Variation: 105 - 236 mmJoist separation: c/c 600 mmSystem Weight - c/c 600 mm: 2.82 kg/m²Materials:Pine T0-C24Fibre-reinforced polypropylenePolyamideCold Galvanised Sheet SteelPoint Load Limit (50 x 50 mm):Load next to screw over joist edge - 9.72 kNLoad between screws over joist edge - 15.85 kN

CHALLENGE The first of its kind for Quebec, the “living street” required a paving grid that would provide multi-purpose access along the street whilst also allowing for the aesthetically pleasing natural look to be maintained. A woonerf is a living street that is traditionally implemented as a traffic calming aid and to enforce low speed limit areas. They are often shared space streets where equal priority is given to all modes of transportation including automobiles, bicycles and pedestrians; usually with separate rights of way. The province of Quebec was looking to do a “pilot project” in the city of Montreal to create a woonerf that would not only provide the required access, including disabled access but that would also have a long-lasting beneficial impact on the environment. They were looking for an environmentally friendly ground reinforcement product which would provide the strength and durability required for a heavily used area. As a “living street”, the product needed to allow the growth of natural vegetation and contain no harmful preservatives which could affect the environment in which it is placed. The harsh weather conditions in Quebec also needed to be considered. With such extreme conditions in both winter and summer, the material needed to withstand the temperature fluctuations. Ground reinforcement products traditionally used such as concrete are susceptible to cold crack in winter as it is a porous material. As a requirement, the desired product was to absorb only limited heat in order to promote growing vegetation. The only suitable material for a project with such challenging conditions was hanit®’s recycled plastic heavy duty ground girds, with their durability and environmental credentials meeting the requirements.SOLUTIONhanit®’s Heavy Duty Ground Grids are manufactured from a blend of high-quality recycled plastic polyolefins extracted from post-industrial and post-consumer mixed waste plastics. Heavy Duty Ground Grids have a high impact resistance which makes them suitable for all vehicle access. They have an interlocking system which improves stability and also allows for quick and simple installation. As the woonerf needed to provide numerous different access levels it was important that the Heavy Duty Ground Grids were versatile. They can be filled with either grass, seed/topsoil or gravel. For this project, wheelchair access was provided through a gravel filled pathway.The rest of the “living street” was mostly completed with grass filled areas. As hanit® products transfer limited amounts of heat, they dry out the soil less than concrete. This works as a benefit to the vegetation growing through the grids. Recycled plastic material is not porous and therefore does not absorb any moisture. This gives added benefits in the winter as when absorbed moisture freezes in concrete it causes cold crack. Their open structure also allows for quick infiltration of any rainwater into the ground allowing for sustainable urban drainage requirements to be met.hanit® Heavy Duty Ground Grids are strong and durable and require no maintenance. They are not affected by weathering and decay; therefore once in place, they have a much longer lifespan than any other competing products. Made from 100% recycled material, the woonerf has been an extremely sustainable project. Providing Montreal with a living street has not only added more vegetation to the area but also allows the city to contribute to an environmentally responsible sustainable urban drainage solution. As the products are chemically inert they do not affect the environment and are harmless to all flora and fauna. In total the project has used 8,500 units of Heavy Duty Ground Grids. This equates to almost 77 tonnes of recycled plastic waste which has been saved from going to landfill. The woonerf has been an extremely well celebrated project that has won prizes for its conception and green initiatives. “I recommend Les Dalles Vertes (Heavy Duty Ground Grids) to all my clients. We laid out nearly 30,000 square feet of these pavers for the Woonerf project and it took us half the time and resources that were required to install the old concrete grass pavers." - Tony Scirocco, Ventec

Britannia Leisure Centre is a new multi-sport community complex in Hackney. A key driver for the client was that the building should have a compact footprint. This was achieved by stacking the facilities, creating a rooftop MUGA with tennis courts and 5-a-side football pitches.Lang+Fulton supplied the external steel mesh panels which crown the building and provide panoramic views of London. These were made from their Terra-34 grating which features an anti-climb aperture. The tall slender panels were designed to continue the architectural theme of the building’s columns and vertical elements and were finished in a graphite grey ppc to compliment the neutral palette of stone, concrete and glass.In addition a grating screen was supplied to secure the upper levels of the stairway providing natural daylight and through visibility to the entrance atrium and cafe area.The steel grating also conformed to the requirement for material durability and low maintenance which were key specification considerations.The Britannia Leisure Centre has received multiple awards including Overall Building of the Year (New London Architecture).

THE PROJECTLocated on the south bank of the River Thames, this iconic building is being renovated and built into a thriving neighbourhood full of culture, art and history. Within the area, you can live, eat, shop and explore a range of places and living options.There is a range of apartments within the iconic landmark as well as the building surrounding the power station. Not only do the apartments offer a prime location in London, but they also come with a wide range of amenities included, including unforgettable London views, rooftop gardens, affordable homes, sustainable living plus much more.THE PRODUCTBattersea was built in stages and so were the mailboxes supplied.Phase 1 included full stainless steel RENZ Mailboxes that look absolutely stunning. They are recessed into the wall and include a soft close function for design purposes. These mailboxes look like they could be a brown colour, but that’s the reflection off the floor!The stainless steel has been engraved for easy identification. The boxes are also double-height for more storage capacity. Phases 2 & 3 are completely bespoke solutions to ensure the industrial cultural look of the building is kept throughout the additional finishes. These mailboxes were designed specifically for Battersea Power Station, they are suspended above the ground and in between concrete and steel pillars. These incredible Tileboxes are fitted with bespoke cladding, engraved numbering for easy identification and powder coated in anodic brown with a dark bronze lock.

Smet Supported Partner, Hargreaves Group contracted to M2 Plastering, machine applied the LIDL External Render System in Waterlooville onto Poroton blocks externally using as Base Coat: Bauprotec 850 M – Lightweight Lime Cement Render and as Finish Coat; Mineral Finish Coat K.  As Key Coat: Change of substrate concrete/steel pillar/Poroton block or mass concrete and insulated plinths: Bauprotec RHS Multi-Purpose Render with the addition of Bauprotec SLP for plinths.The Internal Render System specification onto Poroton blockwork consists of a base of Coat: Bauprotec 850 M, Lightweight Lime Cement Render, sponge floated in warehouse areas and skim finished in sales areas. Key Coat: Change of substrate concrete/steel pillar/Poroton block: Bauprotec RHS is used.The LIDL render spec, available from SMET consists of:Bauprotec 850 M is a factory produced Lightweight Lime Cement Render, specially designed for machine or hand application produced to EN 998-1: 2010 and is CE Marked.Bauprotec RHS is a CE Marked, factory-produced highly polymer-modified render specially designed for hand and machine application produced to EN 998-1: 2010.Mineral Finish Coat – K is a CE marked, factory-produced mineral-based, high-quality finish-coat render, specially designed for hand and machine application to EN 998-1, 2010.Bauprotec SLP is a CE Marked, factory-produced Lightweight Sand & Cement Render specially designed for hand and machine application produced to EN 998-1: 2010.The special render properties; lightweight, low thermal conductivity, high yield, and Smet Supported Partner superior technical backup, are key factors in choosing SMET.SMET is committed to delivering consistently superior quality, German-made Render Systems to Lidl Plastering and rendering/plastering contractors across the UK and ROI.  If you’d like to speak to us about your Lidl job – contact SMET.All LIDL spec SMET Render System products are available directly from Smet Building Products Ltd, who ensures the contractor has a superior level of technical back up in the machine application of the LIDL specification.

These are the latest cycle hubs designed, manufactured, supplied and installed by Falco for four hospitals on behalf of Wrightington, Wigan and Leigh NHS Foundation Trust, complete with everything a cyclist may need in order to visit each hospital by bike.Wrightington Hospital, Thomas Linacre Centre and Royal Albert Edward Infirmary, all located within Wigan, Greater Manchester, received a bespoke version of the FalcoHub cycle hub, complete with reinforced safety glass cladding, FalcoLevel-Eco two-tier cycle racks, a cycle pump and repair stand, helmet lockers, powder coating and bespoke branding graphics.All 6m x 3m cycle hubs, capable of accommodating 22 bikes each, are clad in toughened safety glass with bespoke NHS branding graphics chosen by the client and the galvanised steel framework has been powder coated in an attractive ‘Fir Green’ RAL colour. Each cycle repair stand is equipped with a cycle pump and a number of convenient tools in order to carry out basic cycle maintenance whilst on the go.Leigh Infirmary, also based in Greater Manchester, received a bespoke version of the FalcoLok cycle store complete with traditional hardwood cladding, FalcoVert-Pro semi-vertical cycle racks to accommodate 10 bikes and five convenient helmet lockers.All FalcoHub cycle hubs as shown here at Wrightington, Wigan and Leigh NHS Foundation Trust, are a contemporary cycle store manufactured from a combination of a galvanised steel frame and reinforced safety glass / hardwood cladding, designed to be sympathetic to the surrounding area. The FalcoHub was developed by Falco’s in house design team to ensure it met the client’s specification including structural calculations so that the whole design meets the UK/European CPR regulations EN1090 and is CE marked as per UK law.In addition to the cycle hubs shown here, Falco has also recently installed cycle hubs for many locations across the UK including Rochdale Infirmary, Stromness Travel Centre in the Orkney Islands, Crewe, Runcorn, Birmingham International, Warrington Bank Quay and Carlisle station for Avanti West Coast, Bradford Royal Infirmary and St Luke’s Hospital for Bradford Teaching Hospitals NHS Foundation, The Royal Oldham Hospital for Pennine Acute Hospitals NHS Trust, Ninewells Hospital & Medical School in Dundee and a bespoke cycle hub for Leicester City Council.For more information about the project here at Wrightington, Wigan and Leigh NHS Foundation Trust or how Falco can assist your cycle parking scheme, please contact our helpful sales team on 01538 380080.

BACKGROUND: The Pavilion was being refurbished, ready to be re-open as a new café to help increase tourism to the town.Plans included creating a new terrace at the front, a small rear extension, and a portable office/store at the back.REQUIREMENT: A modular ramp to the terrace for pedestrian and wheelchair use. END RESULT:Our installers fitted a Rapid Ramp, which included a pedestrian walkway with a loading capacity of 1,000kgs. It is designed to safely support the weight of varies public traffic, including walkers, prams, wheelchairs, and mobility scooters.The installation was completed within a few hours on a snowy late evening.FEATURES INCLUDED: Mesh Platform - self-draining mesh allows water to pass through rather than collect on the surface.Trombone Ends - these are added to the ends of a Rapid Ramp to prevent clothes catching.Telescopic Legs - these can be adjusted to accommodate threshold heights.Continuous Handrail - this handrail system ensures users always have a support to hold onto.Standard Colour Black - ramps are powder-coated black to create a hard finish that is tougher than conventional paint.EXTRA FEATURES INCLUDED:Infill Handrail - this product prevents users from climbing or falling through gaps.Yellow Tread - this is a safety feature designed to help those with impaired vision identify the nose of the ramp and helps users distinguish any level changes.CONCRETE VS PEDESTRIAN METAL RAMP INSTALLATIONS:Unfortunately, newly poured concrete must be protected from freezing for the first 24 to 48 hours and requires drying time before use. Therefore, concrete installations are heavily reliant on good weather conditions, and cannot be completed in snow or frozen temperatures.Unlike concrete, our pedestrian ramps can be installed in most weather conditions, including snow. Plus, the product is manufactured from galvanised steel.Galvanising is a process where a protective coating of zinc is applied to prevent rusting and to kill moss.

Armourcoat’s modular panel system ArmourFX has been specified to stunning effect at the new G-Shock store on London’s Carnaby Street by Double Retail. The new flagshop concept store was designed to physically interpret the core values of the brand and clearly segment G-Shock’s extensive product range.Through the careful use of lighting and materials, such as slate flooring, hot rolled steel surfaces and concrete wall panels from ArmourFX,the environment is an embodiment of G-Shock toughness.The store has elevated this premium offering and created a versatile future-proof space adaptable for specific collections and product launches.ArmourFX concrete effect panels are ideal for a deconstructed urban look for contemporary projects. The panels offer a wealth of design options to achieve a distinctive industrial style including distressed effects or recessed ‘shutter’ markings. Off-site construction is fast becoming the method of choice for both contractors and their clients with projects under tight deadlines for completion, or where it is impractical to work with ‘wet’ plastering trades on site. ArmourFX modular solutions can be highly customized to suit the client, sent directly to site and installed in a few hours. Photography: © Max McClure

Architect/Designer: PRPLocation: ManchesterProject Overview: 30 Brown Street is a four-storey brick office building originally built in 1985. The brief was to retain and refurbish the building to provide circa 50,000sqft of adaptable contemporary workspace. ServiceFull hardware scheduling & bespoke finishProject DetailsThis exciting design in the heart of Manchester steers away from using traditional finishes such as stainless steel or brass and instead incorporates a bold use of white RAL9010 PPC ironmongery. Architect David Sharpe explains why‘The building has a lot of exposed raw finishes, including concrete soffits and grey terrazzo flooring, partly inspiring the name, CORE (also referring to the location in the heart of Manchester's office core). Doors and main structural elements were painted a very dark grey to provide a clear contrast with the concrete structure. The inspiration behind the choice of white ironmongery was to provide a high quality counterpoint to the darker raw exposed concrete and painted finishes, and any small part metalwork - eg the lighting, brassware and glazed partition framing, were also specified to be white to match.The contemporary interior was a key ingredient for the brief and although we started with the concept of a mixture of grey and white ironmongery to work with the overall feel of the building during our close work with the architect this was pulled back to a predominantly white scheme with grey pull handles being used for fully glazed doors to create greater contrast and to fulfil the contemporary brief.The choice of specific ironmongery took into account the desire for a minimalist aesthetic, relating to the choices in lighting and brassware.’To find out more about this project visit www.prp-co.uk/project/30-brown-street.html

150 CheapsideBauder Hot Melt structural waterproofing systemSynopsis150 Cheapside is a new-build office development in the City of London, offering some 182,740 square foot of office space on eight floors. Overlooking St. Paul’s Cathedral, this landmark construction has recently gained an ‘Excellent’ BREEAM rating.Bauder Building BoardProject:              150 CheapsideLocation:           LondonRoof Area:         2000m2Investor:            St Martin’s Property InvestmentsArchitect:          Michael Auckett ArchitectsContractor: Knight AsphaltThe specificationThe client, St. Martins Property Investments, opted to use the Bauder extensive green roof finish, combined with Bauder’s Bakor waterproofing build up - a durable hot melt system installed at a comparatively low cost compared to traditional felt solutions.The resultWith both the waterproofing and the sedum blanket finish being sourced from one supplier, complete compatibility was guaranteed providing the client with an ‘immediate’ green roof finish and waterproofing build up with a life expectancy in line with that of the structure.System installedBauder Bakor 790-111 BauderPLANT E 42Torch-on root-resistant capping sheet green2 790-11 with reinforcement layerHot melt rubberised bitumen asphalt with a percentage of post-consumer recycled materials that infills and fully bonds to all minor deviations in the deck.3 DeckPrimed concrete.

A high-profile project, involving the unique new Sconnex® type W thermally insulating wall connection, is Haberdashers’ Boys’ School, just north of London.   It is one of the UK’s leading independent boys' schools and sets exemplary standards, in both educational terms and in its facilities as well.  Demonstrated by the new reinforced concrete extension to the Preparatory School, where cube_design architects were commissioned to produce a design for three additional classrooms and relocated changing facilities.  Jane Lock-Smith, the founder of cube_design and RIBA Client Design Advisor within the Building Schools for the Future programme, observes: “The design is respectful to the style of the existing building, but offers a contemporary twist through the use of full height glazing and charred timber cladding. A colonnade also minimises the buildings footprint.  Our detailing took into account that around 40% of all thermal bridges in a building are caused by walls and supports.  The Schöck product offers an application-friendly, high-quality solution that contributes to a permanently sustainable building concept”.   The outstanding insulation performance is combined with an excellent load bearing capacity, which transmits very high pressure, tensile and shear forces, both in the longitudinal and transverse direction. The ultra-high performance pressure buffer achieves compressive strength levels in excess of 175 N/mm2. Sconnex® type W also achieves a significant cost reduction when compared with the installation of insulation beneath the floor slab.  

Fulham JettyBauder Bakor 790-11 hot melt structural system with Bauderflex waterproofing system and BauderGREEN sedum systemSynopsisFulham Wharf is a landmark regeneration scheme that began in 2013 and included the ecological enhancement of an abandoned jetty on the River Thames. This redevelopment was designed to provide the local community with an ecological education centre and bio-diverse wildlife reserve.Bauder Building BoardProject:Fulham JettyLocation:LondonRoof Area:1,000m²Specifier:FabrikApproved Contractor:Accurate RoofingProject challenges One of the major challenges for this roof was installing the central sloped section, which required exceptional levels of technical input and workmanship. This roofing area was waterproofed with the same bituminous green roof system as the upper roof; however a special timber design for retaining the substrate and sedum blanket was also needed. Since its official opening in October 2013, the lower wildflower roof has become a haven for a variety of different birds and insects.The resultThe building’s new roof swoops down to become a continuum with the jetty deck and is covered with a green habitat providing three distinct environments for wildlife; one on the flat roof, one on the slope and the third on the jetty deck. The education centre roof was waterproofed with Bauder’s root resistant bitumen membrane before then having a sedum blanket fitted. On the lower roof, 650m² of Bauder’s hot melt structural waterproofing was installed along with a wildflower blanket, providing an instant carpet of vegetation. Systems installedBauderflex bituminous waterproofing system1 BauderPLANT E 42A torch applied, SBS elastomeric bitumen capping sheet. The product features chemically treated bitumen to deliver superior root resistance which has been tested and approved by the FLL. The membrane is reinforced with 250g/m² spunbond polyester fleece to allow the finished product to cope with structural movement without fracture.2 BauderTEC SPRINT DUOSelf-adhesive bitumen underlayer with “DUO” lap technology to ensure thorough sealing of lap joints, even in lower temperatures. The product features a glass fleece reinforcement for strength and stability. The product benefits from cleaner, safer, and faster installation than traditional torch-applied membranes.3 BauderPIR FA-TELightweight, PIR flatboard insulation board with aluminium foil facing on both sides. This product has zero ozone depletion potential.4 BauderTEC KSD FBSSelf-adhesive air and vapour control layer with a mica finished upper surface to allow easy bonding of insulation using the specified Bauder Insulation AdhesiveBauder Bakor 790-11 hot melt waterproofing system1 BauderPLANT E 42Torch-on root-resistant, green capping sheet. Reinforced with spunbond polyester fleece to allow the finished product to cope with structural movement without fracture.2 790-11 with reinforcement layerHot melt rubberised bitumen asphalt with a percentage of post-consumer recycled materials that infills and fully bonds to all minor deviations in the deck.3 DeckPrimed concrete.Bauder XF 301 Sedum system1 BauderGREEN XF 301Sedum vegetation blanket instantly providing at least 90% coverage on an extensive green roof. Integrated water retention and filter layer.2 BauderGREEN AL 4040mm high perforated edge/drainage trim frames and retains the Bauder XF 301 sedum system.3 BauderGREEN SDFMulti-functional drainage and filtration layer which prevents the roots of sedum plants from becoming waterlogged.4 BauderPLANT ETorch-on root-resistant capping sheet green