Verified by manufacturer 3 months ago
A lightweight, non-penetrating, mechanically attached EPDM warm roof system.
Suitable for profiled metal deck applications and other deck types which provide sufficient anchorage for mechanical attachment.
The RubberGard™ EPDM RMA System is a lightweight, non-penetrating mechanically attached system developed around the QuickSeam™ RMA strip: a strip of reinforced EPDM membrane incorporating two strips of self-adhesive QuickSeam™ Splice Tape laminated along each edge over the length of the strip.
Features and benefits:
System components:
Color | Black |
Material | Rubber Polyisocyanurate (PIR) |
Uniclass | |
CAWS | J42/10 Warm deck roof covering J42/110 Warm deck roof covering |
Preparation | - |
Horizontal work | SA-19 Primer.Firestone SA-19 Primer is used to prime and prepare exterior concrete, wood, and metal surfaces to enhance the adhesion of Firestone V-Gard vapour control membrane. It's also used to prime seams when required. |
Skirtings and vertical work | SA-19 Primer.Firestone SA-19 Primer is used to prime and prepare exterior concrete, wood, and metal surfaces to enhance the adhesion of Firestone V-Gard vapour control membrane. It's also used to prime seams when required. |
Air and vapour control layer | - |
Type | V-Gard Vapor Control layer.Firestone V-Gard Vapor Control Membrane is designed to be used as a vapour control layer in Firestone roofing systems. It consists of a reinforced aluminium foil with self-adhesive bituminous backing protected by a release film. The fibreglass reinforcement makes it suitable for applications that involve high mechanical stresses. The Firestone V-Gard membrane can be installed on concrete, wood and steel deck. |
Attachment | Self-adhesive bituminous backing. |
Insulation | - |
TypeConsult the manufacturer's Technical Services Department for R-Value/U-value calculations as required. | ISOGARD AK PIR Insulation.Thermal conductivity: 0.023 W/m.K. Thickness: 30–160 mm. Insert requirements. Firestone ISOGARD AK insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gastight multi-layered aluminium complex. ISOGARD MG PIR Insulation.Thermal conductivity: 0.025–0.028 W/m.K. Thickness: 30–160 mm. Insert requirements. Firestone ISOGARD MG insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gasopen mineral glassfibre facer. RESISTA AK PIR Insulation.As per Fully Adhered Warm Roof System spec. Thermal conductivity: 0.023 W/m.K. Thickness: 30–160 mm. Insert requirements. Firestone RESISTA AK insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gastight multi-layered aluminium complex. RESISTA MG PIR Insulation.As per Fully Adhered Warm Roof System spec. Thermal conductivity: 0.025–0.028 W/m.K. Thickness: 30–160 mm. Insert requirements. Firestone RESISTA MG insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gasopen mineral glassfibre facer. |
Attachment | Insulation plates and fasteners.The fastening pattern is chosen in line with the manufacturer's installation guidelines and to accommodate for wind loading. |
Waterproof covering | - |
Type100% cured non-reinforced, Ethylene-Propylene-Diene Terpolymer (EPDM) synthetic rubber, manufactured in an ISO 9001 and ISO 14001 registered facility. Minimum unspliced width of 3.05 m. Specification compliance: UL Classified/ FM Approved. ASTM D 4637/ EN 13956 (CE Mark). 7500 hrs of Artificial Ageing as per EN 1297. | RubberGard™ EPDM LSFR Roofing Membrane 1.1 mm.RubberGard™ EPDM LSFR Roofing Membrane 1.5 mm. |
Attachment | QuickSeam RMA strip.Secured to the steel deck using approved plates/batten bars and fasteners. Spacing of the plates and/or fasteners differs to accommodate for wind loadings and are positioned according to the parameters of the wind load calculation based on local or international standards. |
Joints | Lap splices: 100 mm minimum overlap with 76 mm QuickSeam Splice Tape. |
Surface protection | QuickSeam Walkway Pads.760 x 760 mm high quality rubber pads with QuickSeam Tape factory laminated to the bottom. They are used for protection of the Firestone RubberGard EPDM membrane in areas of regular roof traffic (periodical maintenance around mechanical equipment, access doors, etc.). |
System accessories | QuickSeam Splice Tape.QuickSeam FormFlash.QuickSeam Flashing.QuickSeam SA Flashing.QuickSeam Reinforced Perimeter Fastening Strip.QuickSeam Universal Pipe Flashing.QuickSeam Conduit Flashing.QuickSeam Penetration Pocket.QuickSeam Walkway Pad.QuickPrime Plus.Lap Sealant HS.All Purpose (AP) Fasteners.Heavy Duty (HD) Fasteners.Splice Wash (SW-100).Cleaner C-20.Water-Block Seal (S-20).Pourable Sealer S-10 (Parts A & B).Coiled Metal Batten Strip.Metal Batten Strip.Termination Bar. |
Corners | QuickSeam FormFlash (external corners) and folded internal corners. |
Pipes | Pipe penetrations: QuickSeam FormFlash. Pipe penetrations: QuickSeam Pipe boots and Conduit Flashing. |
Outlets | Drains: Install Water Block Sealant between membrane and outlet bowl. Secure membrane mechanically to outlet using integral clamping ring. Drains: Insert outlet bedded on Water Block Sealant. Secure and flash with QuickSeam FormFlash or SA Flashing. |
Walls | Wall terminations: Termination bar, fastened with Water Block Sealant and Lap Sealant HS installed along top edge. @200mm (maximum) o.c. Wall terminations: Metal batten bar fastened with surface mounted or inserted metal counter flashing protection. @150mm (maximum) o.c. Wall terminations: Metal capping or concrete coping stones. Wall termination: Preformed metal edge trim. An appropriate metal edge trim will be prefabricated and installed with fasteners @ maximum 100 mm centres. The edge trim will be sealed with QuickSeam Flashing. |
Platform | Compatible | Version |
---|---|---|
![]() | - | 1 |
RubberGard™ EPDM Ballasted Warm Roof System
RubberGard™ EPDM Fully Adhered Warm Roof System
RubberGard™ EPDM Inverted Warm Roof System
UltraPly™ TPO Inverted Warm Roof System
UltraPly™ TPO Ballasted Warm Roof System
UltraPly™ TPO Fully Adhered Warm Roof System
UltraPly™ TPO Mechanically Attached Warm Roof System