Newton Waterproofing Systems
Protecting Buildings Since 1848
+44 (0)1732 360095 www.newtonwaterproofing.co.uk
Showing 37-72 of 73
Newton 408 DeckDrain
Newton Waterproofing Systems
Newton 408 DeckDrain is a double cuspated, deck and flat roof drainage membrane, that incorporates a polypropylene geotextile filter layer, bonded to a water impermeable HDPE (High Density Polyethylene) core. The double cuspated design provides two layers of drainage; allowing for primary drainage through the geotextile filter, as well as secondary drainage between the underside of 408 DeckDrain and the primary waterproofing layer. The lower drainage layer eliminates the risk of trapped water, a problem associated with conventional single cuspated deck drainage membranes.
Newton 409 RootBarrier Puncture Resistant Root Barrier Membrane
Newton Waterproofing Systems
Newton 409 RootBarrier is designed to eliminate root penetration. It consists of an impermeable High Density Polyethylene
(HDPE) membrane, providing robust root-proof protection to the primary waterproofing membrane to green roofs or
planters where intrusive root systems are present. The membrane has high tensile strength and puncture resistance and provides an efficient, reliable and cost effective
barrier to provide protection against Japanese Knotweed and other aggressive root systems.
Newton 410 Geodrain
Newton Waterproofing Systems
Newton 410 GeoDrain is a two-core drainage sheet consisting of a non-woven, geotextile filter layer, thermally welded to a water impermeable HDPE (High Density Polyethylene) drainage membrane.
Newton 420 Reservoir Green Roof Drainage Membrane
Newton Waterproofing Systems
Newton 420 Reservoir is a unique drainage and water-retention membrane for use where a water reservoir is required for extensive green roofs of sedum, herbaceous plants, mosses or grass above decks and roofs.
Unlike other products of this type, Newton 420 Reservoir has a bonded geotextile that prevents intrusion of the soil into the water holding cups during back-fill and compression. This results in a permanently larger volume reservoir than any
other 20mm-deep green roof membrane.
When the water holding cups are full, the large drainage holes within the HDPE core allow water to easily pass through to the drainage layer below to prevent saturation and water logging of the green roof above.
Newton 503 Cavity Drain Membrane
Newton Waterproofing Systems
Newton 503 is a high quality cavity drain waterproofing membrane, supplied in a plain
variant for walls and floors and a meshed variant for receiving plaster or render to walls, and
used within Newton System 500, our internally applied waterproofing system that includes
Newton drainage and pumping systems. Depending on the variant, Newton 503 is suitable
for the waterproofing of earth retained walls, vaulted soffits and floors, is guaranteed against
deterioration for 30 years, has a life expectancy of at least 50 years (DIN 9001:2000), and is
supported by BBA Certification Number 94/3010.
Newton 508 Cavity Drain Membrane
Newton Waterproofing Systems
Newton 508 is a high quality dimpled cavity drain waterproofing membrane, which is supplied in a number of variants for use within Newton System 500, our, internally applied waterproofing system that includes Newton drainage and pumping systems. Depending on the variant, Newton 508 studded membrane is suitable for the waterproofing of earth retained walls, vaulted soffits and floors and is guaranteed against deterioration for 30 years, with a life expectancy of at least 50 years (DIN 9001:2000) and is supported by BBA Certification Number 94/3010.
Newton 520 eco
Newton Waterproofing Systems
Newton 520 eco is a cavity drain waterproofing membrane made from recycled High Density
Polyethylene (HDPE). It is one of the main constituent parts of Newton System 500, our
BBA Certified, Type C cavity drain system, used for waterproofing of floors within earthretained
structures, that includes drainage channels sited below the membrane for increased
drainage capacity. With its 20 mm deep stud profile, Newton 520 eco is used within Newton
System 500 as a high drainage capacity floor membrane and is generally specified where it
is anticipated that there may be a risk of severe water penetration.
Newton 601 Slimline
Newton Waterproofing Systems
Newton 601 Slimline is a high-grade flooring membrane used primarily for isolating moisture-sensitive flooring from dampness in the floor slab.
Newton 603
Newton Waterproofing Systems
Newton 603 is a high quality flooring membrane suitable for use above new and existing floors. The 3mm studs allow for pressure equalisation of dampness within the floor below allowing for dissipation at room perimeter and subsequent drying of the floor.
Newton 701-HB
Newton Waterproofing Systems
High Build Epoxy Floor Coating Two-component solvent free epoxy resin based floor coating developed to provide protective and decorative properties to concrete, steel and other substrates.
Newton 802-DPM Data Sheet
Newton Waterproofing Systems
BBA certified, 100% recycled, 1200 gauge damp proof membrane for use below concrete floors or screeds where no groundwater pressure is expected. Newton 802-DPM is compatible with all common building materials, and suitable for numerous applications as a DPM, vapour barrier, or as a slip membrane, screeding membrane or curing membrane.
Newton 803 Damproofing Membrane
Newton Waterproofing Systems
BBA certified, high quality damp proof membrane for use above ground. Can be used as an alternative to Newton 803 Newtonite and 805 Newlath where a meshed surface is not required as a surface for direct plastering or rendering.
Newton 803 Newtonite
Newton Waterproofing Systems
BBA certified damp proof membrane, comprising of high density polyethylene membrane with a rot-proof polythene mesh that is heat-welded during the manufacturing process to the surface of one side. The meshed surface creates a mechanical key to allow the membrane to be plastered, rendered or to receive dot & dab plasterboard.
Newton 805 Newlath
Newton Waterproofing Systems
An internally applied, composite damp proof membrane comprising of high-density polypropylene membrane with a rot-proof polythene mesh heatwelded during the manufacturing process to the surface of one side. The meshed surface creates a mechanical key to allow the membrane to be plastered, rendered or to receive dot & dab plasterboard.
Newton 806 CWC
Newton Waterproofing Systems
A white thermal coating for cold and poorly insulated surfaces. It contains specific mineral powders which, thanks to their insulating features, warm the surface of the treated wall.
Newton 807 BKK
Newton Waterproofing Systems
A transparent, colourless wall coating, water and siloxane based, ideal to protect porous walls of various substrates from wind-driven rain. After treatment, the wall is deeply impervious to water ingress and so better protected against frost damage. The treated wall will continue to dry and vapour drive is not effected due to the coating being very vapour permeable.
Newton 809-DPC High Load Physical Damp Proof Course
Newton Waterproofing Systems
BBA certified, high performance damp proof course that will not extrude under extreme load, and will not affect the ability of a well designed and built wall to sustain and transmit compression. Compatible with all common building materials and suitable for all designs for different damp proof courses.
Newton 901-P Data Sheet
Newton Waterproofing Systems
Newton 901-P is a two-part, solvent free, clear epoxy which is applied to damp and porous surfaces as a pre-primer prior to the application of Newton 902-P, a vapour barrier and primer for newly placed, or damp, concrete and screed.
Newton 902-P Data Sheet
Newton Waterproofing Systems
Newton 902-P is a two-part, solvent-free, damp-tolerable, epoxy-based primer which is applied above Newton 901-P
pre-primer as a barrier to residual substrate moisture and vapour within concrete and screeds.
Newton 916 FlexProof Primer Data Sheet
Newton Waterproofing Systems
Newton 916 FlexProof Primer is a polyurethane primer that improves the adhesion of Newton 106 FlexProof to porous substrates, and should always be used when concrete has been ground.
Newton Basedrain
Newton Waterproofing Systems
Newton Basedrain is the drainage system used most commonly within the Newton System 500 waterproofing system. It compromises a range of products that collectively receive water ingressing at weaknesses within the structure and then discharge the collected water to a Newton Sump System or safe drainage
Newton Complete Guide To Waterproofing 2018
Newton Waterproofing Systems
The Newton complete guide to waterproofing includes solutions for new and existing structures. It is comprehensive, includes case studies, product information, the British Standard requirements, grades and types of waterproofing, combination systems, as well as technical help and advice.
Newton Control Panel-Pro
Newton Waterproofing Systems
The Newton Control Panel-Pro is a class-leading pump control panel with many unique features, which has been designed by Newton Waterproofing Systems to provide the ultimate in pump operation and diagnostics.
Newton CP Pumps
Newton Waterproofing Systems
The Newton CP250, CP400 and CP750 are a range of high quality clean water pumps. Ideally suited for the removal of ground water from basements and cellars. Sold in manual and automatic versions and can be purchased as pumps only, or as a key component in our packaged pumping systems.
Newton Fibran XPS 500-C
Newton Waterproofing Systems
Newton Fibran XPS 500-C is a 50mm deep, closed-cell thermal insulation board made from rigid extruded polystyrene foam (XPS).
Newton High Water Alarm
Newton Waterproofing Systems
The Newton High Level Water Alarm PA50 has been designed to detect high water levels within pump sump chambers and is included within the Newton Titan-Pro and Newton Titan pumping systems. The alarm is battery operated and uses a standard 9V PP3 battery.
Newton NP400 Pump
Newton Waterproofing Systems
A high head and high to medium performance pump. The NP400 is available as an automatic pump, or as a manual pump for use with our pump control systems.
Newton NP400W
Newton Waterproofing Systems
Effluent Pump Medium head and medium performance pump for dishwasher, washing machine, bath/shower waste (not sewage)
Newton NP750 Pump
Newton Waterproofing Systems
The Newton NP750 is a high performance ground and clean water pump. The NP750 is available as an automatic pump or as a manual pump for use with our pump control systems. The NP750 is available as pump only, or as a key component in our Newton Titan-Pro packaged pump systems.
Newton NP750W Pump
Newton Waterproofing Systems
The Newton NP750W is a high head and high performance effluent pump for the removal of waste water from the Newton Titan-Pro sump chambers or formed concrete chambers.
Newton PAC-500 System Overview
Newton Waterproofing Systems
The Newton PAC-500 System is combined 'Type C' (BS 8102:2009) cavity drain waterproofing and ground gas mitigation system, developed by Newton Waterproofing Systems and Prestige Air Ltd. The addition of the PAC Positive Air Curtain to the System 500 waterproofing provides protection against water, gasses and hydrocarbon vapours from the ground within a single internally applied system.
This system provides basement waterproofing across all environmental grades (Grade 1-3) in accordance with BS 8102:2009, as well as a ground has mitigation system that is integrity tested with tracer gas to confirm viability.
Newton Pump Controller
Newton Waterproofing Systems
The Newton Pump Controller is designed to be used with matched pairs of Newton NP400, NP400W, NP750 or SP750C Cutter manual pumps and provides a sophisticated, yet simple to install, twin pump control system which offers some of the features of the Newton Control Panel-Pro, but at a much lower cost.
Newton SP750 Cutter
Newton Waterproofing Systems
The Newton SP750 Cutter is a high quality sewage pump, incorporating a tungsten carbide tipped cutting impeller that rotates against a serrated suction cover in order to cut solid waste before pumping, resulting in a much lower risk of blockage than similar sized vortex impeller pumps.
Newton Titan-Pro
Newton Waterproofing Systems
The Titan-Pro Pumping System is designed to be used specifically with our Newton System 500 waterproofing system. It includes features and components for connection with Newton System 500 drainage products.
The unique design provides simple connectivity and ease of installation when used with the Newton drainage products; Newton Basedrain and Newton Floordrain, as part of the Newton System 500 waterproo ng system. The sump chamber is designed to have all the inlet and outlet connections to be always at the same height relative to the Newton drainage products.
Newton Titan-Pro
Newton Waterproofing Systems
The Titan-Pro packaged sump system is designed specifically to be used with Newton System 500.The adjustable neck allows for the sump to be installed at a fixed height relative to the slab.
Newton Victron Inverter Range
Newton Waterproofing Systems
The Victron range of pure sine wave Inverters/Chargers provide advanced solutions to ensure that Newton pumping systems continue pumping during power interruption, by inverting 12V DC power from a battery (or multiple batteries) to clean and efficient 230V power.
Showing 37-72 of 73