A-Z
Showing 73-108 of 132
Newton HydroBond 403 Plus
Newton Waterproofing Systems
A high-performance, self-healing membrane with a locking fleece on the inner surface and a hydrophilic polymer coating externally. The membrane is BDA approved, NHBC accepted as Type A waterproofing, and the gas barrier variant provides resistance to radon, carbon dioxide and hydrocarbons.
HydroBond 403 Plus provides a complete waterproof envelope to the structure to achieve Type A (barrier) waterproofing suitable for Grades 1, 2 and 3 as defined by BS 8102:2022, are suitable for all below ground and earth-retained structures from domestic basements to the largest civil engineering projects, and can be used as part of the HydroBond® System with HydroBond 108-LM which is sprayed to the exposed walls of the basement after the temporary formwork is removed.
Newton HydroBond 403 Plus BDA Certificate
Newton Waterproofing Systems
A high performance, self-healing membrane with a locking fleece on the inner surface and a hydrophilic polymer coating externally. The membrane is BDA approved, NHBC accepted as Type A waterproofing, and the gas barrier variant provides resistance to radon, carbon dioxide and hydrocarbons.
Newton HydroBond 410 GeoDrain TDS
Newton Waterproofing Systems
Externally Applied Drainage Membrane
Newton HydroBond Protection Board TDS
Newton Waterproofing Systems
Bitumen Protection Board for Waterproofing Membranes
Newton HydroCoat 104 Super TDS
Newton Waterproofing Systems
Crystalline Waterproofing
Newton HydroCoat Tanking Slurry SDS
Newton Waterproofing Systems
Newton HydroCoat Tanking Slurry Safety Data Sheet
Newton HydroTank 301-EP Metal Waterbar
Newton Waterproofing Systems
HydroTank 301-EP Metal Waterbar is a coated metal waterbar system used for the sealing of construction joints within retained concrete structures.
HydroTank 301-EP Metal Waterbar features a flexible, adherent coating on one side, which is covered with a granular material.The rough coating creates a permanent watertight seal with the surrounding concrete to create a waterbar that works immediately, without requiring activation by water as required with hydrophilic waterbars.
Newton HydroTank 306 Swell Mastic
Newton Waterproofing Systems
HydroTank 306 Swell Mastic is a high-quality, firm, fast-curing, swellable, single-component, polymeric adhesive sealant. The special composition of Newton 306 SwellMastic makes the sealant start to swell when in contact with water (to about 150% of original size).
The sealant has high elasticity and high adherence and it develops a strong adhesive tensile strength immediately after application. The first swelling is time delayed which allows HydroTank 306 Swell Mastic to be applied to slightly damp surfaces.
Newton HydroTank 315 Waterbar
Newton Waterproofing Systems
HydroTank 315 Waterbar is a hydrophilic, acrylate polymer waterbar, which swells when activated by moisture. It is characterised by high elasticity and high tensile strength. HydroTank 315 Waterbar can be used to seal the structure against water leaks to both cast-in-place concrete and precast construction joints.
Newton HydroTank 315 Waterbar BDA Certificate
Newton Waterproofing Systems
A high-grade, hydrophilic waterbar with high elasticity and high tensile strength, made from a polymer which swells when in contact with moisture. Ideal for sealing structures against water leaks to both cast-in-place concrete and precast construction joints.
Newton HydroTank 315 Waterbar TDS 1.8
Newton Waterproofing Systems
Newton NewCoat / DampSafe 901 Primer TDS
Newton Waterproofing Systems
Two-part, solvent-free and clear epoxy, applied to damp and porous surfaces as a pre-primer prior to the application of Newton DampSafe/NewCoat DPM, a vapour barrier and primer for newly placed or damp concrete and screed.
Newton NewCoat 701-HB
Newton Waterproofing Systems
High Build Epoxy Floor Coating Two-component solvent free epoxy resin based floor coating developed to provide protective and decorative properties to concrete, steel and other substrates.
Newton NewLath 805 Mesh Membrane
Newton Waterproofing Systems
An internally applied, composite damp proof membrane comprising of either 3mm HDPE or 5mm HDPP membranes with a rot-proof polythene mesh that is heat welded during the manufacturing process to the surface of one side. The meshed surface creates a mechanical key to allow the membrane to be plastered, rendered or to receive dot & dab plasterboard.
Newton NewSeal 409 Root Barrier
Newton Waterproofing Systems
Newton 409 RootBarrier is designed to eliminate root penetration. It consists of an impermeable High Density Polyethylene
(HDPE) membrane, providing robust root-proof protection to the primary waterproofing membrane to green roofs or
planters where intrusive root systems are present. The membrane has high tensile strength and puncture resistance and provides an efficient, reliable and cost effective
barrier to provide protection against Japanese Knotweed and other aggressive root systems.
Newton NewSeal 420 DeckDrain
Newton Waterproofing Systems
NewSeal 420 DeckDrain is a unique drainage and water-retention membrane for use where a water reservoir is required for extensive green roofs of sedum, herbaceous plants, mosses or grass above decks and roofs.
Unlike other products of this type, NewSeal 420 DeckDrain has a bonded geotextile that prevents intrusion of the soil into the water holding cups during back-fill and compression. This results in a permanently larger volume reservoir than any
other 20mm-deep green roof membrane.
When the water holding cups are full, the large drainage holes within the HDPE core allow water to easily pass through to the drainage layer below to prevent saturation and water logging of the green roof above.
Newton Newtonite TDS
Newton Waterproofing Systems
Non-Meshed Damp Proofing Membrane
Newton NP400 TDS
Newton Waterproofing Systems
A high head and high to medium performance pump. The NP400 is available as an automatic pump, or as a manual pump for use with our pump control systems.
Newton NP400W TDS
Newton Waterproofing Systems
Effluent Pump Medium head and medium performance pump for dishwasher, washing machine, bath/shower waste (not sewage)
Newton NP750 TDS
Newton Waterproofing Systems
The Newton NP750 is a high performance ground and clean water pump. The NP750 is available as an automatic pump or as a manual pump for use with our pump control systems. The NP750 is available as pump only, or as a key component in our Newton Titan-Pro packaged pump systems.
Newton NP750W Pump TDS
Newton Waterproofing Systems
The Newton NP750W is a high head and high performance effluent pump for the removal of waste water from the Newton Titan-Pro sump chambers or formed concrete chambers.
Newton PAC-500 System Overview
Newton Waterproofing Systems
The Newton PAC-500 System is combined 'Type C' (BS 8102:2022) cavity drain waterproofing and ground gas mitigation system, developed by Newton Waterproofing Systems and Prestige Air Ltd. The addition of the PAC Positive Air Curtain to the Cavity Drain Waterproofing provides protection against water, gasses and hydrocarbon vapours from the ground within a single internally applied system.
This system provides basement waterproofing across all environmental grades (Grade 1-3) in accordance with BS 8102:2022, as well as a ground has mitigation system that is integrity tested with tracer gas to confirm viability.
Newton Pump Controller Controller Operation Manual
Newton Waterproofing Systems
TWIN PUMP CONTROLLER FOR ALL MANUAL PUMPS
Newton Pump Controller TDS
Newton Waterproofing Systems
The Newton Pump Controller is designed to be used with matched pairs of Newton NP400, NP400W, NP750 or SP750C Cutter manual pumps and provides a sophisticated, yet simple to install, twin pump control system which offers some of the features of the Newton Control Panel-Pro, but at a much lower cost.
Newton SP750 Cutter TDS
Newton Waterproofing Systems
The Newton SP750 Cutter is a high quality sewage pump, incorporating a tungsten carbide tipped cutting impeller that rotates against a serrated suction cover in order to cut solid waste before pumping, resulting in a much lower risk of blockage than similar sized vortex impeller pumps.
Newton System 500 Ancillaries TDS
Newton Waterproofing Systems
Ancillaries
Newton Titan Operating Manual
Newton Waterproofing Systems
Compact Pumping Systems
Newton Titan TDS
Newton Waterproofing Systems
Compact Pumping Systems
Newton Titan-Pro Pump System
Newton Waterproofing Systems
The Titan-Pro Pumping System is designed to be used specifically with our Cavity Drain waterproofing system. It includes features and components for connection with Cavity Drain Waterproofing drainage products.
The unique design provides simple connectivity and ease of installation when used with the Newton drainage products; Newton Basedrain and Newton Floordrain, as part of the Newton System 500 waterproo ng system. The sump chamber is designed to have all the inlet and outlet connections to be always at the same height relative to the Newton drainage products.
Newton Titan-Pro Pump System TDS
Newton Waterproofing Systems
The Titan-Pro packaged sump system is designed specifically to be used with Newton System 500.The adjustable neck allows for the sump to be installed at a fixed height relative to the slab.
Newton Titan-S Installation Manual
Newton Waterproofing Systems
Surface Water Pumping System
Newton Titan-S TDS
Newton Waterproofing Systems
Surface Water Pumping System
Newton Trojan pro TDS
Newton Waterproofing Systems
Foul & Surface Water Pumping System
Newton Trojan-Pro Operating Manual
Newton Waterproofing Systems
Foul & Surface Water Pumping System
Newton Victron Inverters TDS
Newton Waterproofing Systems
Inverter/Charger Battery Back-Up - 500VA to 1600VA
Newton-High Water Level Alarm
Newton Waterproofing Systems
The Newton High Level Water Alarm PA50 has been designed to detect high water levels within pump sump chambers and is included within the Newton Titan-Pro and Newton Titan pumping systems. The alarm is battery operated and uses a standard 9V PP3 battery.
Showing 73-108 of 132