NBS Source
Newton Waterproofing Systems

Newton Waterproofing Systems

Protecting Buildings Since 1848

+44 (0)1732 360095 www.newtonwaterproofing.co.uk

Sort by:

Showing 37-72 of 111

Newton CDM 520 eco Floor

Newton CDM 520 eco Floor

Newton Waterproofing Systems

CDM 520 eco Floor is a cavity drain waterproofing membrane made from recycled High Density Polyethylene (HDPE). It is one of the main constituent parts of Cavity Drain Waterproofing, our BBA Certified, Type C cavity drain system, used for waterproofing of floors within earthretained structures, that includes drainage channels sited below the membrane for increased drainage capacity. With its 20 mm deep stud profile, CDM 520 eco Floor is used within Cavity Drain Waterproofing as a high drainage capacity floor membrane and is generally specified where it is anticipated that there may be a risk of severe water penetration.
Newton CDM BaseBoard TDS

Newton CDM BaseBoard TDS

Newton Waterproofing Systems

Above slab drainage conduit
Newton CDM Basedrain TDS

Newton CDM Basedrain TDS

Newton Waterproofing Systems

The drainage system comprises of a range of products that collectively receive water ingressing at weaknesses within the structure and then discharge the collected water to a Newton Sump System or safe drainage (drainage that is below the level of the basement floor that cannot back up or block): Basedrain - Drainage conduit for the perimeter of the area to be waterproofed, that is situated at the base of the wall membrane Floordrain - Drainage conduit for collection of water at the construction joint to the floor and to replace Basedrain at door thresholds. Floordrain is also used to connect the perimeter Basedrain to the sump Corner - Formed 90 degree corner Basedrain T-Piece - Formed T for a 90-degree connection to the Floordrain from the Basedrain
Newton CDM Fibran XPS-500C TDS

Newton CDM Fibran XPS-500C TDS

Newton Waterproofing Systems

CDM Fibran XPS-500C is a 50mm deep, closed-cell thermal insulation board made from rigid extruded polystyrene foam (XPS).
Newton Complete Guide To Waterproofing 2018

Newton Complete Guide To Waterproofing 2018

Newton Waterproofing Systems

The Newton complete guide to waterproofing includes solutions for new and existing structures. It is comprehensive, includes case studies, product information, the British Standard requirements, grades and types of waterproofing, combination systems, as well as technical help and advice.
Newton Control Panel-Pro TDS

Newton Control Panel-Pro TDS

Newton Waterproofing Systems

The Newton Control Panel-Pro is a class-leading pump control panel with many unique features, which has been designed by Newton Waterproofing Systems to provide the ultimate in pump operation and diagnostics.
Newton CP150/250/400/750

Newton CP150/250/400/750

Newton Waterproofing Systems

Ideally suited for the removal of ground water from basements and cellars. Sold in manual and automatic versions and can be purchased as pumps only, or as a key component in our packaged pumping systems. The unique vertical operation float switch ensures that the pumps operate within their footprint, removing the possibility of the float snagging during operation and allowing the pumps to be used within smaller sumps. The vertical float switch is also highly adjustable, allowing the pump switching height to be adjusted between the ‘on’ and ‘off’ positions, as well as the height relative to the pump. The Newton CP Pumps are suitable for use with Newton Victron Power Inverters to give continual pumping even during power outage.
Newton DAB E.Box TDS

Newton DAB E.Box TDS

Newton Waterproofing Systems

The DAB E.Box is an electronic control panel for the protection and automatic operation of one or two submersible pumps installed in domestic, civil and industrial environments. The panel is best paired with dual Newton SP sewage pumps within sewage and foul pumping systems – it is simple to install and provides a robust solution for sewage pumping systems, enclosed in an IP55 rated casing.
Newton DampSafe + NewCoat SDS

Newton DampSafe + NewCoat SDS

Newton Waterproofing Systems

Damp Tolerable Pre-Primer For Porous Surfaces
Newton DampSafe / NewCoat DPM Data Sheet

Newton DampSafe / NewCoat DPM Data Sheet

Newton Waterproofing Systems

DampSafe / NewCoat DPM is a two-part, solvent-free, damp-tolerable, epoxy-based primer which is applied above NewCoat / DampSafe 901 Primer as a barrier to residual substrate moisture and vapour within concrete and screeds.
Newton DampSafe 601 Slimline

Newton DampSafe 601 Slimline

Newton Waterproofing Systems

DampSafe 601 Slimline is a high-grade flooring membrane used primarily for isolating moisture-sensitive flooring from dampness in the floor slab.
Newton DampSafe 603 TDS

Newton DampSafe 603 TDS

Newton Waterproofing Systems

DampSafe 603 is a high quality flooring membrane suitable for use above new and existing floors. The 3mm studs allow for pressure equalisation of dampness within the floor below allowing for dissipation at room perimeter and subsequent drying of the floor.
Newton DampSafe 802-DPM

Newton DampSafe 802-DPM

Newton Waterproofing Systems

Newton DampSafe 802-DPM Data Sheet

Newton DampSafe 802-DPM Data Sheet

Newton Waterproofing Systems

BBA certified, 100% recycled, 1200 gauge damp proof membrane for use below concrete floors or screeds where no groundwater pressure is expected. DampSafe 802-DPM is compatible with all common building materials, and suitable for numerous applications as a DPM, vapour barrier, or as a slip membrane, screeding membrane or curing membrane.
Newton FlexProof 106 TDS

Newton FlexProof 106 TDS

Newton Waterproofing Systems

Highly advanced single component liquid waterproofing material, which forms an elastomeric polymer membrane that is rainproof in minutes and capable of handling severe building movements and deformations. The FlexProof 106 System is composed of two variants of the product, plus ancillaries: X1 – A thixotropic variant that is applied as a paste and so is suitable as a surface sealant over joints. NV – A lower viscosity variant that can be poured and is typically used within movement joints. FlexProof 106 Primer (Product code: 916) – Improves adhesion to porous surfaces. FoamStop (Product codes: FS1 to FS8) – Foam backing rod for movement joints. The animation to the right shows the correct application of FlexProof 106-X1 to a concrete construction joint.
Newton HydroBond 108-LM BDA Certificate

Newton HydroBond 108-LM BDA Certificate

Newton Waterproofing Systems

Highly radon resistant, cold spray-applied, seamless rubber waterproofing membrane for the external waterproofing of basements (including covered decks) and foundation walls.
Newton HydroBond 108-LM Membrane

Newton HydroBond 108-LM Membrane

Newton Waterproofing Systems

Newton HydroBond 108-LM is a cold spray-applied, seamless, rubber waterproofing membrane for the external waterproofing of basements and foundation walls. Normally specified as part of our HydroBondTM System in conjunction with HydroBond 403 Plus, the membrane can also be used on its own, terminating to raft or strip foundations. 108 HydroBond-LM is very quick to apply, at up to 1000m2 per day, and is not subject to the delays normally associated with liquid membranes as it can be applied in cooler and damper conditions and in most cases without a primer.
Newton HydroBond 109-LM TDS

Newton HydroBond 109-LM TDS

Newton Waterproofing Systems

HydroBond109-LM is a flexible, single-component, cold-applied, seamless rubber waterproofing membrane with a number of uses for the external waterproofing of basements, foundation walls, decks, and flat roofs. HydroBond 109-LM is also adept as a detailing membrane for the termination and jointing of other Newton waterproofing products, and with its very high adhesive properties it is the perfect primer for adhesion of butyl products to concrete and mortar. Applied by brush, roller or airless spray machine, HydroBond 109-LM can be applied in cool and damp conditions and without a primer.
Newton HydroBond 314 Bentonite Granules

Newton HydroBond 314 Bentonite Granules

Newton Waterproofing Systems

HydroBond 314 Bentonite Granules is a naturally occurring sodium bentonite granules used for detailing to the Newton HydroBondTM System, specifically where HydroBond 403 Plus terminates to otherwise difficult to detail building elements, such as piled walls, support piles, pile caps, and protrusions through the membrane.
Newton HydroBond 403 Plus

Newton HydroBond 403 Plus

Newton Waterproofing Systems

A high-performance, self-healing membrane with a locking fleece on the inner surface and a hydrophilic polymer coating externally. The membrane is BDA approved, NHBC accepted as Type A waterproofing, and the gas barrier variant provides resistance to radon, carbon dioxide and hydrocarbons. HydroBond 403 Plus provides a complete waterproof envelope to the structure to achieve Type A (barrier) waterproofing suitable for Grades 1, 2 and 3 as defined by BS 8102:2022, are suitable for all below ground and earth-retained structures from domestic basements to the largest civil engineering projects, and can be used as part of the HydroBond® System with HydroBond 108-LM which is sprayed to the exposed walls of the basement after the temporary formwork is removed.
Newton HydroBond 403 Plus BDA Certificate

Newton HydroBond 403 Plus BDA Certificate

Newton Waterproofing Systems

A high performance, self-healing membrane with a locking fleece on the inner surface and a hydrophilic polymer coating externally. The membrane is BDA approved, NHBC accepted as Type A waterproofing, and the gas barrier variant provides resistance to radon, carbon dioxide and hydrocarbons.
Newton HydroBond 410 GeoDrain

Newton HydroBond 410 GeoDrain

Newton Waterproofing Systems

HydroBond 410 GeoDrain is a two-core drainage sheet consisting of a non-woven, geotextile filter layer, thermally welded to a water impermeable HDPE (High Density Polyethylene) drainage membrane.
Newton HydroSeal 107 Elastic 2K BDA Certificate

Newton HydroSeal 107 Elastic 2K BDA Certificate

Newton Waterproofing Systems

Cementitious coating for the waterproofing and protection of concrete and masonry. Can be spray-applied so ideal for large projects. Suited to the waterproofing of reservoirs, tunnels, water tanks, basements, podium decks, flat roofs and balconies.
Newton HydroSeal 107 Elastic 2K Membrane

Newton HydroSeal 107 Elastic 2K Membrane

Newton Waterproofing Systems

HydroSeal 107 Elastic 2K is a two-component, cementitious, polymer-rich coating for the waterproofing and protection of concrete and masonry. Capable of withstanding heads of water pressure to 10 bar, both positively and negatively. HydroSeal 107 Elastic 2K is ideally suited to the waterproofing of reservoirs, tunnels, water tanks, basements, podium decks, at roofs, balconies and terraces, and is especially capable where the structure has both masonry and concrete elements where differential movement is expected.
Newton HydroSeal 203-RM

Newton HydroSeal 203-RM

Newton Waterproofing Systems

Single-component, fast-setting, Portland cement-based structural mortar, used primarily for the durable repair of concrete. Ideal for roads, runways, bridges, decks, floors and footpaths. Polymer-modified, and fibre-reinforced, HydroSeal 203-RM is physically and chemically compatible with the host concrete, quickly exhibiting high adhesive and compressive strength. As a single component, requiring only the addition of water, the resulting mortar is rapid curing with enhanced polymeric properties and reliable strength development which is not significantly affected by low temperature use. The mortar can be used as supplied up to 100mm deep, or bulked out with clean, washed, sharp sand to form a high performance screed or for floor or deck repairs up to maximum depth of 300mm.
Newton HydroSeal 313-WP

Newton HydroSeal 313-WP

Newton Waterproofing Systems

Fast Setting Polymer Compound to Seal Leaks HydroSeal 313-WP WaterPlug is a fast setting, polymer compound that instantly stops running water or seepage through masonry or concrete substrates.
Newton Hydroseal 903 Primer TDS

Newton Hydroseal 903 Primer TDS

Newton Waterproofing Systems

For cementitious membranes
Newton HydroSeal 905-CM TDS

Newton HydroSeal 905-CM TDS

Newton Waterproofing Systems

Water based curing membrane
Newton HydroTank 301-EP Metal Waterbar

Newton HydroTank 301-EP Metal Waterbar

Newton Waterproofing Systems

HydroTank 301-EP Metal Waterbar is a coated metal waterbar system used for the sealing of construction joints within retained concrete structures. HydroTank 301-EP Metal Waterbar features a flexible, adherent coating on one side, which is covered with a granular material.The rough coating creates a permanent watertight seal with the surrounding concrete to create a waterbar that works immediately, without requiring activation by water as required with hydrophilic waterbars.
Newton HydroTank 306 Swell Mastic

Newton HydroTank 306 Swell Mastic

Newton Waterproofing Systems

HydroTank 306 Swell Mastic is a high-quality, firm, fast-curing, swellable, single-component, polymeric adhesive sealant. The special composition of Newton 306 SwellMastic makes the sealant start to swell when in contact with water (to about 150% of original size). The sealant has high elasticity and high adherence and it develops a strong adhesive tensile strength immediately after application. The first swelling is time delayed which allows HydroTank 306 Swell Mastic to be applied to slightly damp surfaces.
Newton HydroTank 315 Waterbar

Newton HydroTank 315 Waterbar

Newton Waterproofing Systems

HydroTank 315 Waterbar is a hydrophilic, acrylate polymer waterbar, which swells when activated by moisture. It is characterised by high elasticity and high tensile strength. HydroTank 315 Waterbar can be used to seal the structure against water leaks to both cast-in-place concrete and precast construction joints.
Newton HydroTank 315 Waterbar BDA Certificate

Newton HydroTank 315 Waterbar BDA Certificate

Newton Waterproofing Systems

A high-grade, hydrophilic waterbar with high elasticity and high tensile strength, made from a polymer which swells when in contact with moisture. Ideal for sealing structures against water leaks to both cast-in-place concrete and precast construction joints.
Newton NewCoat / DampSafe 901 Primer TDS

Newton NewCoat / DampSafe 901 Primer TDS

Newton Waterproofing Systems

Two-part, solvent-free and clear epoxy, applied to damp and porous surfaces as a pre-primer prior to the application of Newton DampSafe/NewCoat DPM, a vapour barrier and primer for newly placed or damp concrete and screed.
Newton NewCoat 701-HB

Newton NewCoat 701-HB

Newton Waterproofing Systems

High Build Epoxy Floor Coating Two-component solvent free epoxy resin based floor coating developed to provide protective and decorative properties to concrete, steel and other substrates.
Newton NewLath 805 Mesh Membrane

Newton NewLath 805 Mesh Membrane

Newton Waterproofing Systems

An internally applied, composite damp proof membrane comprising of either 3mm HDPE or 5mm HDPP membranes with a rot-proof polythene mesh that is heat welded during the manufacturing process to the surface of one side. The meshed surface creates a mechanical key to allow the membrane to be plastered, rendered or to receive dot & dab plasterboard.
Newton NewSeal 408 DeckDrain

Newton NewSeal 408 DeckDrain

Newton Waterproofing Systems

NewSeal 408 DeckDrain is a double cuspated, deck and flat roof drainage membrane, that incorporates a polypropylene geotextile filter layer, bonded to a water impermeable HDPE (High Density Polyethylene) core. The double cuspated design provides two layers of drainage; allowing for primary drainage through the geotextile filter, as well as secondary drainage between the underside of 408 DeckDrain and the primary waterproofing layer. The lower drainage layer eliminates the risk of trapped water, a problem associated with conventional single cuspated deck drainage membranes.

Showing 37-72 of 111