"foamglas®"

The NHS Estates Team required a new office space and workshop area and proposed the refurbishment of an existing building.Systems in useHyranger®Starcoat® PMMAOverviewAxter Ltd were instructed by William Gough & Sons Ltd to produce a design for six roof areas, following a site survey report. The project included a mixture of new build and refurbishment areas, comprising of various systems and design requirements. This included a cut to falls insulation design to comply with Part H and BS 6229:2018. Roof A, the focus of this case study, had a series of convex or ‘barrel roofs’, requiring bespoke detailing and careful design to achieve robust detailing and the required U-value.The project value was circa £1 million. This included all building works and a strict budget for the roofing package, which was achieved. The programme for the works was 16 weeks and completed in Autumn of 2022, to the required deadline.The successful project was also nominated for a National Federation of Roofing Contractors (NFRC) award 2023.ChallengesAxter were appointed at RIBA Stage 2 to undertake site surveys and work alongside the Principal Designer as Designer under the Construction Design and Management Regulations 2015.The existing asphalt had shown signs of cracking and blistering, and the outlets were damaged from vegetation growth from a lack of maintenance. New outlets were installed with leaf guards, allowing free flowing water whilst preventing blockages.The proposed office section of the works required thermally upgrading to comply with Building Regulations: Part L. The U-Value requirement was 0.18W/m2K which could be achieved with a 120mm PIR flat board. Due to the curved profile of the roof, installing the insulation below deck level was considered. However, due to an inadequate ceiling height this was disregarded.Furthermore, this would have resulted in the development of interstitial condensation. Further design solutions had to be considered. To bend a 120mm board would have required multiple cuts to the insulation so the decision was made to split this into two thinner boards to achieve the radius more easily.When split into two layers the requirement changed to 2 x70mm boards (140mm total) as worked out using U-Value calculations by the in-house design team at Axter. A timber hard edge was introduced to abut the insulation at the building perimeter to separate the façade and the main field area.Systems and productsAxter’s Hyranger multi-layer RBM system was used across all six roof areas. The system is fully BBA and BRoofT4 compliant, and achieves a guarantee period of 20 years. For this project, Axter’s Goldshield Guarantee was chosen, which covers materials, workmanship and design liability. This was overseen on site by Axter’s Quality Assurance team, who audited the project inclusive of the installation, safety and general management of the roofing works.Axter Starcoat PMMA was used as a cost effective solution to coat the copper fascia and provide a fresh and seamless look to the exterior of the building.SolutionsThe Axter Hyranger multi-layer RBM system was installed using traditional gas driven torches to fully bond the (AVCL) Air and Vapour Control Layer and cap sheet layers. The underlayer was installed over a tissue faced PIR and therefore needed to be self-adhesive in order to reduce the risk of fire, complying with NFRC Safe2Torch guidelines. A cold applied Starcoat PMMA liquid was installed to the façade to achieve a seamless and cost-effective upgrade.The Axter Quality Assurance Team regularly attended site and were in constant communication with the appointed Axtershield Installer, Empire Roofing operatives, to ensure that the system was being installed correctly and to the expected standards in order to achieve the Goldshield guarantee required by the client. To achieve the guarantee level, all materials and workmanship had to be installed as per the Axter specification.The site agent from the main contractor was also regularly on site to oversee the project and ensure that deadlines and timescales were being achieved to keep the build on target for completion. The installation of the multiple roof areas was achieved to exceptional standards leaving the client very impressed with the workmanship.AcknowledgmentsWilliam Gough & Sons Ltd were very impressed with Axter Ltd on our first scheme with them at George Eliot Hospital in Nuneaton. The requirements of the scheme, which included a complex barrelled roof were investigated on site early in the design phase of the project and Axter’s recommendations were swiftly proposed and agreed with the client’s Architect. Once the design requirements had been established one of Axter’s approved installers were employed by us to very successfully deliver the scheme. The 20 year Goldshield guarantee provided for the Reinforced Bituminous Membrane system offered peace and mind to our client. Chris Hinton, Senior QS, William Gough & Sons

Building an outdoor garden and entertaining space with a fab kitchen area that’s the envy of all your friends and neighbours is something many of us only dream about. The new series of Love Your GardenIn the new series of Love Your Garden with Alan Titchmarsh, landscaping experts Cotswold Garden Renovation Services LTD built a beautiful stone columned kitchen with a porcelain slab countertop using Power Grab ‘n’ Bond to secure everything in position for a long-lasting finish, guaranteed to last for a lifetime. Harry & Jamie only use the best materialsHarry Barnes & Jamie Johnstone of Cotswold Garden Renovation are leading the great garden revolution. They’ve shown that with passion and skills anything is possible and provide landscaping expertise for ITV’s Love Your Garden alongside garden designers Alan Titchmarch, Francis Tophill, David Domoney, Katie Rushworth and Danny Clarke.They believe in always using the best quality tools, materials and trusted brands. Power Grab ‘n’ Bond is developed by leading British manufacturers CT1, the No1 sealant and adhesive in the UK. CT1 is always leading and providing the industry with the very latest technology. Now thanks to its unique ‘Tribrid®’ technology Power Grab ‘n’ Bond is a revolutionary product in the field of heavy-duty versatile bonding. Building a outdoor kitchen using Power Grab ‘n’ BondIn their latest project Harry and Jamie hand built a series of vertical stone columns that were then braced together with wide metal strips. Usually these would have to be fitted using mechanical fixings, requiring holes to be drilled through the stone and heavy bolts fitted with their thick heads protruding above the metal braces. As 20mm porcelain slabs were being fitted on top, these protruding bolts were going to be a major issue. Power Grab ‘n’ Bond provided the perfect solution as it’s the ultimate grab adhesive, eliminating the use of mechanical fixings completely and coupled with the rapid curing will, in most projects, save 50% labour time and cost.Using a heavy-duty caulking gun, Harry and Jamie applied Power Grab ‘n’ Bond straight from the cartridge, onto the metal braces and after 4-5minutes fixed directly them into place. Why use Power Grab ‘n’ Bond?With phenomenal initial grab, this fast curing, non-shrinking and almost odourless adhesive secured the braces firmly with immediate effect.Three times stronger than regular hybrid polymers, the ‘Tribrid®’ technology in Power Grab n Bond ensures longer colour retention, incredible durability and flexibility, even when applied outdoors.Yet Power Grab ‘n’ Bond will remain flexible and resist vibrations caused by cooking equipment, barbecuing and constant use. It won’t dry out, nor become brittle and works perfectly in temperatures ranging from 90°C right down to the mind numbing cold -40°C. Power Grab ‘n’ Bond will successfully stick to any material in most applications Not only does it successfully stick all metals (including alloys), but Power Grab also ‘n’ Bond has a capacity to adhere to a wide range of materials such as stone, granite, ytong, marble, concrete, wood, MDF, fiberglass, glass, polystyrene, mirrors and most plastics (except PP, PE and PTFE). Furthermore, its ability to bond combined materials such as wood to concrete or stainless steel to stone is incredible. Power Grab ‘n’ Bond removes the need for mechanical fixings!Originally created for facades and heavy stonework such as the installation of quoins, the versatility, strength and reliability of Power Grab ‘n’ Bond means it now used more widely by professional shop and kitchen fitters as well as specialist trades, landscapers and bathroom installers. It is tested by a UKAS Accredited lab to BS EN 12003 (Determination of shear adhesion strength of reaction resin adhesives) and BS EN1308 (Determination of slip resistance).After fitting the braces Harry and Jamie applied Power Grab ‘n’ Bond to the top side of the metal strips and laid 900x900x20mm thick heavy duty porcelain slabs in place to form the countertop of the external kitchen. How strong is Power Grab ‘n’ Bond?Power Grab ‘n’ Bond is a single part solvent free solution, with a far greater density, allowing phenomenal initial grab, even on vertical installations, and offers a final tensile strength of 22kg per cm2 when fully cured. These metal braces and porcelain slabs aren’t going anywhere soon and will provide a lifetime of outdoor dining for the homeowners. Where can I get Power Grab ‘n’ Bond?Grab also ‘n’ Bond is made in Britain with British technology and British design. Its available now in all good builders merchants nationwide and online from www.ct1.com

Like a lot of homeowners, William Oakley had an under-utilised part of his house. In his case an old outbuilding that had been used for storing the accumulation of life’s odds and ends. Lockdown saw high growth in repurposing previously neglected parts of people’s homes to better suit their lifestyle and leisure choices. William decided a new soundproof cinema room would be a far better use of this space, giving his family a much-needed entertainment area.This is the space William Started withWilliam engaged Cinema Rooms Ltd, a specialist AV equipment supplier and One Off Studio Ltd who specialise in the build and installation of Home Cinemas and Studios.Due to the proximity of the proposed soundproof cinema room to neighbouring properties, it was decided to investigate what acoustic treatments were available. Without adequate acoustic insulation, William’s neighbours may have been subjected to significant noise pollution resulting in potential neighbourhood disputes.Following a quick online search, William found iKoustic, a leading UK supplier of acoustic solutions. Discussing the available options with William and his installation team, iKoustic’s experts were able to advise on the most appropriate system to meet his needs. This included MuteClip, MuteCradle and Tecsound SY70, the quick and easily installed acoustic system providing market-leading acoustic benefits.iKoustic acoustic expert Richard Woodhouse explained, ‘Finding the right solution was imperative for all parties. The system we proposed using MuteClip, MuteCradle and Tecsound SY70 was a cost-effective solution to a complex but often seen problem. The impact of unwanted noise is such an emotive issue in noisy neighbours’ scenarios often resulting in easily avoided disputes if the right materials are included in the project from the outset. iKoustic take pride in sharing our knowledge with installers and end users to ensure the job is right the first time, saving expensive and intrusive remedial work.’Maciek Helfer of One-Off Studio commented, ‘This is the first time I’ve worked with the MuteClip and MuteChannel acoustic system. It was so quick and easy to install. I also found it very useful I could FaceTime Richard at iKoustic with any installation queries when building the soundproof cinema room’. Simon Gregory of Cinema Rooms enthusiastically added, ‘We only work with the highest specification brands and products to bring customers the best Home Cinema experience. The iKoustic team’s expertise and products fall into this category and we’ll definitely be using them again.’William’s soundproof cinema room is now fully operational and thanks to iKoustic his family can enjoy the latest blockbusters in glorious surround sound late into the evening, while his neighbours enjoy a peaceful night safe in the knowledge the biggest Hollywood stars will only be joining William. William commented, ‘We finally got to test out the soundproofing for the first time today with some serious SPL! The system has worked beautifully, barely a whisper outside. Fantastic job iKoustic!’https://www.ikoustic.co.uk/systems/floating-floors-and-under-screed/mutecradle-1630mm-concreteMuteCradle 16/30 was used to create a raised floor with the added benefit that the cradle and packers also allow accommodation of unevenness within the subfloor.The raised floor not only improves acoustic performance but allows servicing to be run through the floor void. Ideal for a soundproof cinema room.Wallshttps://www.ikoustic.co.uk/systems/masonry-wall/muteclip-stud-doubleMuteClip® Stud Double consists of an independent stud frame treated around the perimeter with Isolation Strip F5, MuteClip and MuteChannel are installed to the face of the stud. A double layer of 15mm acoustic board with Tecsound SY70 sandwiched between the two boards is then installed to MuteClip Channels.The system not only adds significant mass to the partition, but the layers of mass are decoupled from the structure by MuteClip. MuteClip is, in effect, a shock absorber – creating a ‘buffer’ between layers of mass and the core construction.The depth of the wall system also allows for servicing to run through the wall cavity of the soundproof cinema room.Ceilinghttps://www.ikoustic.co.uk/systems/timber-ceiling/muteclip-lp-doubleAs the ceiling height was restricted initially and further reduced by specifying a floating floor, MuteClip® LP (Low Profile) was used to minimise further loss in height.MuteClip LP again is a mini-shock absorber that decouples layers of mass from the core construction.With MuteClip LP you recess the clip and most of the channel into the joist cavity with channels running parallel to joists, this leaves just a few mm of channel sitting proud of the bottom of the joists – an acoustic benefit of MuteClip but with little encroachment on head height. This works great in a soundproof cinema room.If you are looking to build a soundproof cinema room you can contact ikoustic and our friendly team will guide you with everything you need to know to get started. Contact us today.

Protecting detection systems is vital to fire safety with only a functioning smoke alarm able to protect you in an emergency.Landlord regulations and Government policesLandlords have responsibilities to keep tenants safe in their properties by providing functioning life safety equipment.Regulations introduced in 2015 require private sector landlords to ensure they ‘have at least one smoke alarm installed on every storey of their properties’ as a legal requirement.There is also a proposed change to this regulation, coming into effect later this year, which will mean social housing is also included, making it mandatory that all rented accommodation must have working smoke alarms fitted. It will also be compulsory for landlords to repair or replace any faulty alarms as soon as they are made aware of defects.Fines up to £5000To protect their tenant, it is the landlord’s responsibility to ensure detectors are fitted and working at the start of every new tenancy agreement. Failure to comply with The Smoke and Carbon Monoxide Alarm Regulations introduced in 2015 can result in a hefty fine of up to £5000.One exasperated landlord wrote online that in one of his properties “Two of the detector heads have been tampered with, presumably so that the tenants can smoke in their rooms”. Consequently, this had been causing false fire alarms and it is up to the landlord to repair or replace the alarm.In some extreme cases, landlords have discovered that smoke alarms have been removed all together from properties, due to disturbances when cooking, smoking, etc. It is then up to the landlord to replace the alarm, and so it is advisable to invest in measures to prevent the alarms removal; some recommendations have been made in government legislations such as BS 5839-6:2019.Ultimately, landlords should feel obligated to ensure regular testing of smoke alarms and the replacement of batteries in their properties to reduce the risk of void insurance or a remedial notice. Simply testing smoke alarms can also help to prevent any danger to tenants and damage to properties should a fire occur.BS 5839-6:2019The latest recommendations in BS 5839-6:2019 are primarily concerned with saving lives and reducing injuries caused by fire, but also covers reducing property damage, which can be extremely costly to landlords in the case of fires.The guidance in BS 5839-6:2019 suggests that in environments such as HMOs, where multiple occupants can be disturbed by false alarms, landlords could alter their smoke alarms systems to have delays before the signal is sent to all tenants for the occupier to investigate the cause. This can help to reduce complacency during false fire alarms or the temptation to dangerously compromise smoke alarms.The recommendation also states that landlords should seek alternative smoke alarms that can alert to intervention or disablement of the alarm in the event of tenants continually tampering.Tenants’ responsibilityAlthough it is the landlords legal duty to provide working smoke alarms in all properties, tenants must not tamper with smoke alarm, remove them, cover them up or in any other way damage or prevent them from operating in their intended manner. Failure to comply with this could result in the tenant facing a substantial fine, or termination of their tenancy agreement.It falls to the tenants to take their own safety into consideration and should contact landlords if there are any issues with smoke alarms, such as false fire alarms, so their landlord can test and replace the batteries, or alarms themselves if necessary. Preventing alarms from effectively detecting fires can result in fatal incidents and also fines for misconduct falling to the tenants.One student at Edinburgh University covered the smoke alarm in his room with bubble wrap whilst living in student accommodation. Preventing the smoke detector from working effectively proved a dangerous mistake when a fire started in his room and he had to be pulled to safety after being found struggling to escape the flames while the building was being evacuated. As a consequence for this reckless behaviour, he was fined and ordered to pay £1000 in compensation after being arrested and pleading guilty.Steel Web Stoppers®  Safety Technology International is a specialist manufacturer of a range of fire, safety and security products; their wire cages help to prevent tampering with essential life safety equipment, such as smoke alarms.STI’s Steel Web Stoppers®  are designed to protect against vandalism, misuse and damage to smoke and fire detectors. Constructed from plastic coated, heavy-duty galvanised steel rod, the Steel Web Stoppers can withstand the severest of abuse from vandalism or accidental damage. It also prevents tampering with the alarm, without hindering legitimate use, therefore still allowing the landlord to service the device and replace batteries when appropriate.

A classic Parisian apartment is benefitting from the thermal effectiveness of the introduction of the innovative ultra-thin Spacetherm® WL insulation.Located in the 11th arrondissement in the heart of Paris on Boulevard Voltaire and overlooking the Place de la Republique, the two-bedroom, 135sqm apartment was built in the Hausmann style. Hausmann’s renovation of Paris was part of a major programme commissioned by Emperor Napoléon III in the late 19th century, resulting in the distinctive appearance of the wide avenues, parks and squares which have become associated with this beautiful city.Property owner Keirnan Murphy has made a significant investment in the renovation of the apartment to improve overall comfort, energy efficiency and to reduce heating costs.Keirnan explains, “The solid stone walls, whilst adding to the building’s charm, result in heating inefficiencies and higher heating costs. During summer the stone walls warm during the day, retaining and radiating heat throughout the night. In winter, the solid walls cool down leading to a huge increase in heating costs.We undertook lots of research on solutions for green and energy-efficient renovations. In the research, we considered products available within France and as well as those available internationally. The Spacetherm WL aerogel insulation from the A. Proctor Group was a perfect choice for the apartment. At just 13mm thickness, the Spacetherm WL fits inside the lip of our cornices, which average about 20mm. Typically the walls of these older properties are not completely flat and so the option of an ultra-thin insulation was critical. Most alternatives were thicker and would not have worked.We are very pleased with the results and we noticed that when leaning up against the Spacetherm WL you can feel your back warm against the insulation. The A. Proctor Group were extremely helpful in addressing all the questions from the architect and ourselves. They also provided comprehensive support and guidance to our builder on the installation.”Spacetherm WL is a high-performance laminate specifically designed to be fixed to the internal surfaces of existing solid walls without the need for mechanical fixings. Spacetherm WL consists of Spacetherm aerogel insulation blanket bonded to 3mm Magnesium Board (MgO), for use in applications where improved thermal performance is required with limited space.Typically, a solid wall will have a U value of around 2.1 W/m2K. Following the application of Spacetherm WL, this can be reduced to around 0.8 W/m2K, dependent on the wall structure.

ClientManchester University NHS Foundation Trust (MFT) Market SectorHealthcare The Project BriefWythenshawe Hospital is a major acute teaching hospital part of the Manchester University NHS Foundation Trust (MFT). Its area of specialisms includes cardiology and cardiothoracic surgery, heart and lung transplants as well as cancer and breast care services and supports patients from across the North West and beyond.During the upgrade of the Emergency Department (E.D) the team decided on both protection and preventative measures to ensure only the highest of standards were adhered to which were in line with the Hospital’s renowned reputation. The SolutionIntastop Ltd was chosen to supply and fit a range of protective products designed specifically to integrate seamlessly with the hospital aesthetics.They included Bed Head Protection, Hand Rails, Sanparrel® Wall Sheet and Corner Guards from the Inpro product range in addition to Intastop’s innovative I-Gienic Smooth Hygienic Sheet and Rigid Frame Guards. Impact protection sheet along with the other products installed at Wythenshawe Hospital boast a plethora of benefits including high impact resistance, Class ‘O’ Fire Rated; tested to BS476 Parts 6 & 7 and available in a variety of colours. Additional Benefits of Impact Protection SheetEnsures staff and patient safety in the event of a fire by maintaining fire integrity of the surface.Protects against localised damage.Maintains a clean, safe environmentAchieves colour contrast for critical surfaces to assist with visually impaired staff and patientsWhat the client saysMarcus Ashurst, project manager for the emergency department said“With a collaborative approach from the inception of the project through to completion, the Trust was mindful that the new emergency department operating 24 hours a day would require careful thought and consideration with regards to the finishes selected. With leading healthcare architects IBI plans were drafted with full engagement with the clinical teams to develop an extremely well-considered and effective design – fit for purpose.Working with Interserve, the principal supply chain partner appointed to construct the new development, Intastop were nominated to supply and install a fully comprehensive system of door and wall protection that would not only withstand and protect the built environment, but also enhance the aesthetics of the environment. The holistic approach taken and end result was indeed most satisfactory.”

Copenhagen’s Amager Bakke is a visionary project in Denmark that doubles as a recreational playground and a waste-to-energy plant.The towering structure is over 280 feet high, has an estimated cost of $670 million and is a part Copenhagen’s commitment to become the world’s first carbon-neutral capital by 2025. Part of the facility is already on line.The waste-to-energy plant, a giant incinerator that burns household garbage to generate heat for approximately 160,000 households and electricity for 62,500 homes, began operating in March. The recreational component is still under construction.Kalwall® translucent sandwich panels provided a critical solution in this truly global project, with their aesthetic beauty, energy efficiency and, most importantly, their best-in-class explosion-venting properties.Kalwall panels are used in areas of the building where a potentially volatile event could occur. The panels work to vent pressure out of the building, allowing it to withstand an explosion without collapsing roofs or floors. The panels are designed to release from their mounting system, but remain attached to the side of the building to avoid becoming falling debris. The interior of the panels are shatterproof and include a Fiber-Reinforced Polymer(FRP) face sheet that can be customied to withstand 230 ft-lbs (312J) of impact.Staying close to the project’s mission of being environmentally conscious, Kalwall panels provide dramatic savings in energy consumption through exceptional thermal and daylighting performance that reduces heating costs and artificial light usage.Working through Sipral, a leading supplier of external building envelopes based out of Prague, the panels were delivered on schedule and required no on-site modifications. Amager Baake was designed by the highly-acclaimed architecture firm Bjarke Ingels Group (BIG) and has the world watching as it merges two completely different applications.BIG founder Bjarke Ingels hopes that Amager Bakke will “change public perceptions of what a public utility should be” by providing a social and physical infrastructure.Amager Bakke provides Copenhagen with a rooftop ski slope that is comprised of 1,600 feet of trails, as well as 10 running and walking trails. There is also a 260-foot climbing wall along the facade.Ingels said the concept of a structure that brings together two diverse interests can be lasting. “If you make a building that remains relevant to the people living around it, and using it and inhabiting it, it can last forever,” Ingels said in an interview with CNN Style.Photography: Christoffer Regild

These are the secure FalcoCrea cycle lockers Falco recently manufactured, supplied and installed for Granton Harbour in Edinburgh – a new waterfront mixed housing development, bringing 306 affordable homes to the north Edinburgh coast.Robust cycle parking was at the forefront of the initial design stage of the flagship development, aiming to provide up to 1,300 residents with a sustainable, cost-effective mode of transport.The City of Edinburgh Council project aims to help more people choose cycling as an affordable and sustainable way of travel for everyday journeys and has been developed in partnership with the nation’s cycling charity, Cycling Scotland and supported by Transport Scotland grant funding.This month, Falco supplied and installed ten FalcoCrea cycle lockers, providing Granton Harbour residents with up to 40 secure cycle spaces, all within an eye-catching, compact cycle locker design.As a registered supplier of sustainable wood, all three Falco shelters have been clad in FSC® certified hardwood, designed to be sympathetic to the surrounding area. Each FalcoCrea cycle store features double doors for easy accessibility and all shelters incorporate cylinder locks for high security.The FalcoCrea has proven to be a highly popular cycle locker since its launch providing local authorities and housing associations with a cycle parking solution which answers three common problems; security, spacing footprint and branding. The FalcoCrea is designed to provide maximum security, within a compact space saving design and fully capable of incorporating branding to promote cycling as a principal mode of transport.The ingenious cycle locker has already been commissioned for a number of schemes across the UK including recent installations at; Moray Carshare charity, The Social Bite Village in Edinburgh, Rouken Glen Park in Glasgow and Barra Airport and Oban Airport.With the use of an electric cycle charging point (FalcoCrea+), the cycle locker can be transformed into a convenient charging hub for electric bikes whilst retaining all of the benefits from the standard model. Additionally, many European housing developments use the FalcoCrea as a combined bin store and cycling store, providing residents with practical yet great looking facility keeping their property neat.For more information about the ingenious FalcoCrea cycle locker please contact our helpful sales team on 01538 380080.

ChallengeTo insulate one of Marks and Spencer’s most carbon efficient premier stores with a holistic approach taken towards key sustainability factors such as water, carbon, biodiversity, the community, materials and waste to landfill.SolutionKnauf Insulation’s FactoryClad Roll 40 was utilised within the 11,000m2 multi-wave form standing seam roof, which was supplied by Euroclad to achieve an outstanding visual, functional and environmentally friendly element of the store design, plus achieving a BREEAM ‘Excellent’ rating. The number of BREEAM credits available from using Knauf Insulation’s Factory Clad Roll 40, played a part in its specification for Marks and Spencer’s flagship sustainable retail store at Cheshire Oaks.Gethin Williams, Euroclad’s Elite Systems Coordinator said: “FactoryClad Roll 40, in 280mm, has a 90/90 lambda value, a generic BRE Green Guide rating of A+ and has excellent thermal and acoustic properties. Thanks to these many characteristics, we thought it was perfect for this project, which resulted in it achieving the relevant BREEAM credits. Being lightweight, flexible and with a high tear strength, fitting was fast and error free, ensuring the thermal integrity was uncompromised.”Knauf Insulation’s FactoryClad Roll 40 is manufactured with ECOSE® Technology, has a thermal conductivity of 0.040W/mK and also has the highest possible Euroclass A1 reaction to fire classification when tested in accordance with BS EN 13501-1.In addition to this, Knauf Insulation’s mineral wool products with ECOSE Technology benefit from a revolutionary, bio-based, formaldehyde-free binder technology, based on rapidly renewable materials, instead of petro-based chemicals – delivering superior environmental sustainability and enhancing the environmental credentials without affecting the thermal, acoustic or fire performance. What’s more Knauf Insulation FactoryClad Roll 40 represents no known threat to the environment and has zero Ozone Depletion Potential and zero Global Warming Potential."Knauf Insulation FactoryClad Roll 40, in 280mm, has a 90/90 lambda value, a generic BRE Green Guide rating of A+ and has excellent thermal and acoustic properties. Thanks to these many characteristics, we thought it was perfect for this project, which resulted in it achieving the relevant BREEAM credits. Being lightweight, flexible and with a high tear strength, fitting was fast and error free, ensuring the thermal integrity was uncompromised."- Gethin Williams, Euroclad’s Elite Systems Coordinator