Bauder Total Green Roof System Reinforced Bitumen Membrane Inverted Roof Covering System Self-Adhered (with Torch-On Capping Sheet)

As 'Horizontal work'.

Self-adhered.

BauderPLANT E.

Guidance for specification option:

Elastomer-bitumen capping sheet with root-resistance according to the FLL. The membrane is reinforced with 250 g/m² spunbond polyester fleece to allow the finished product to cope with structural movement without fracture. Expandable graphite fire retardant is also incorporated to reduce spread of flame.

• Width: 1 m.
• Length: 5 m.
• Thickness: 5.2 mm.
• Weight: 6 kg/m².
• Surface, top: green slate mineral chippings; bottom: thermofusible polyethylene.
• Reinforcement: 250 g/m² recycled spunbond polyester.
• Cold bending test: -36°C.
• Softening point: >120°C.
• Tensile strength: length >1000 N/50 mm; transverse >1000 N/50mm.
• Elongation at break: length >45%; transverse >45%.

Torch applied.

Bauder GRP Trim.

Guidance for specification option:

GRP roof edge trim for use with Bauder bituminous roof systems. Available colours of either grey or black and a choice of profiles to suit the requirements of most projects.

Bauder GRP Water Check Trim.

Guidance for specification option:

GRP water check trim to be used on parapets and perimeter kerbs wider than 200 mm – must not be used on its own as a check kerb.

Available in black only.

Bauder Aluminium Termination Bar.

Guidance for specification option:

Natural finish aluminium alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall.

Bauder GRP Termination Bar.

Guidance for specification option:

Black glass reinforced plastic (GRP) alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall.

Not required.

Bauder LiquiFIBRE Detailing Kit.

Guidance for specification option:

Fast-curing waterproofing resin, containing fibre reinforcement that can be used for detailing awkward shapes or inaccessible areas where using LiquiDETAIL is impractical. PMMA-based resin that requires a catalyst and is solvent-free, isocyanate-free and halogen-free.

Bauder LiquiDETAIL.

Guidance for specification option:

Cold liquid-applied fast-curing waterproofing resin that can be used on upstands and details. PMMA-based resin that requires the addition of catalyst to trigger curing and is solvent-free, isocyanate-free and halogen-free.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Bauder JFRI PREMIUM+ Inverted Insulation.

Guidance for specification option:

Insert required thickness, 85–240 mm in 5 mm increments.

Designed specifically for inverted roof applications.

• Type: Rigid expanded polystyrene (EPS) insulation boards.
• Facing: Unfaced.
• Colour: Grey.
• Nominal weight: 30 kg/m³.
• Standard board size: 1215 x 1215 mm (including 15 mm rebate).
• Thermal conductivity: Declared 0.031 W/m·K; design 0.031 W/m·K (may vary, dependent on thickness specified).
• Design load compressive strength: 0.20 N/mm² with 10% nominal compression.
• Recyclability: 100%.

Consult manufacturer's literature for further details.

Bauder JFRI PREMIUM (300) Inverted Insulation.

Guidance for specification option:

Insert required thickness, 90–240 mm in 5 mm increments.

Designed specifically for inverted roof applications.

• Type: Rigid expanded polystyrene (EPS) insulation boards.
• Facing: Unfaced.
• Colour: White.
• Weight: 40 kg/m³.
• Standard board size: 1215 x 1215 mm (including 15 mm rebate).
• Thermal conductivity: Declared 0.033 W/m·K; design 0.033–0.035 W/m·K (may vary, dependent on thickness specified and application).
• Design load compressive strength: 0.30 N/mm² with 10% nominal compression.
• Recyclability: 100%.

Consult manufacturer's literature for further details.

Bauder XPS (300) Inverted Flatboard.

Guidance for specification option:

Insert required thickness.

• Type: Rigid extruded polystyrene insulation boards.
• Facing: Smooth, self-finished.
• Density: 30 kg/m³.
• Standard board size: 1250 x 600 mm.
• Board thickness: 30 mm, 40 mm, 50 mm, 60 mm, 70 mm, 80 mm, 100 mm, 120 mm, 140 mm.
• Thermal conductivity: 30 mm: 0.034 W/m·K; 40–50 mm: 0.035 W/m·K; >50 mm: 0.036 W/m·K.
• Compressive strength: 0.30 N/mm².

Bauder XPS (500) Inverted Flatboard.

Guidance for specification option:

Insert required thickness.

• Type: Rigid extruded polystyrene insulation boards.
• Facing: Smooth, self-finished.
• Density: 35 kg/m³.
• Standard board size: 1250 x 600 mm.
• Board thickness: 40 mm, 50 mm, 60 mm, 70 mm, 80 mm, 100 mm, 120 mm, 140 mm.
• Thermal conductivity: 40–60 mm: 0.034 W/m·K; >60 mm: 0.036 W/m·K.
• Compressive strength: 0.50 N/mm².

BauderGLAS Inverted Insulation Flatboard.

Guidance for specification option:

Insert required thickness.

• Type: Cellular glass with pre-applied inorganic coating on the topside. Both the core material and the coating have an A1 reaction to fire classification and are therefore non-combustible. Where more than one layer of insulation is required, BauderGLAS Slab T3+ will be used as the base layer.
• Facing: Pre-applied inorganic coating.
• Density: 100 kg/m².
• Standard board size: 600 x 450 mm.
• Board thickness: 100 mm, 120 mm, 140 mm, 160 mm, 180 mm, 200 mm.
• Thermal conductivity: 0.043 W/m·K.
• Compressive strength: 0.4 N/mm.

Loose laid (and suitably ballasted).

Guidance for specification option:

• Setting out: Loose lay insulation directly over the capping sheet to brick pattern with staggered joints. Minimize cutting and avoid small pieces at perimeters and penetrations. Dependent upon the total thickness required, it may be necessary to construct the insulation using two layers of board. The manufacturer/supplier can advise on the available combination options.
• Joints: Butt together.
• Loading over inverted insulation (minimum): Ballast (landscaping) should be installed onto the Bauder WFRL Membrane (Water Flow Reducing Layer) to a minimum depth required to achieve a permanent minimum 80 kg/m² and load which prevents wind uplift and flotation of the insulation in high winds and/or heavy rainfall.
• Additional loading at perimeters: On high buildings in more exposed areas, wind uplift may be a problem and in these instances paving slab ballast must be considered. Paving slabs should be a minimum of 50 mm-thick. The slabs should be laid on paving slab supports of minimum 175 mm diameter (or equivalent base area).
• All final details must to be confirmed with Bauder before proceeding.

Not required.

Bauder lightning conductors.

Guidance for specification option:

Lightning conductor clips are a specially designed secure clip that allows for movement.

• Bauder Lightning conductor clips – Type 4: Polyvinyl chloride (PVC) coated or bare conductor.

Bauder rainwater outlets.

Guidance for specification option:

Bauder has a range of insulated or stainless-steel rainwater outlets.

The insulated outlets can be used for maintaining thermal continuity at drainage points. Suitable for warm, cold and inverted roof construction. The BRE Certified (report no. HPR357-303748) high thermal value of the rigid foam body prevents condensation from forming on the underside of the outlet body.

Designed for use when connecting to conventional drainage systems and is suitable for both new build and refurbishment projects. Outlets are included in the Bauder waterproofing system guarantee as they are integrated components.

Flow rate figures (where applicable) are based on BS EN 12056:3:2000, typically taken using a 35 mm header of water including leaf grille:

• Bauder Bitumen Compact Vertical Outlet DN100: Insulated internal outlet, 6.1 L/s.
• Bauder Bitumen Vertical Outlet DN70: Insulated internal outlet, 7.1 L/s.
• Bauder Bitumen Vertical Outlet DN150: Insulated internal outlet, 7.2 L/s.
• Bauder Bitumen Letterbox Parapet Outlet DN 205 including stainless-steel leaf guard, 2.02 L/s.
• Bauder Bitumen Parapet Outlet DN 100 including stainless-steel leaf guard, 1.06 L/s.
• Bauder Bitumen Vertical Refurb Outlet DN70, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Vertical Refurb Outlet DN95, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Vertical Refurb Outlet DN145, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Parapet ‘Tell-Tale’ Overflow DN50, designed to be used in conjunction with other roof drainage outlets to ensure that there is no water ingress into the build and that the structural load of the roof is not exceeded and provides a visible warning that the roof is holding excessive water.

Bauder rooflights/ glazing/ ventilation.

Guidance for specification option:

All these glazing products are fully compatible with the roof waterproofing systems. Consult manufacturer for details and insert requirements.

• BauderDOME Rooflight.
• Bauder Euroglaze Rooflight.
• BauderFLATGLASS Rooflight.
• Bauder Special Modular Rooflight.
• Bauder Continuous Rooflight.
• Bauder Walk-on Rooflight.
• Bauder Direct Glazing.
• Bauder AOV.
• Bauder Modular Link Glazing.
• Bauder Structural Rooflight
• Bauder Fire Rated Rooflight.