WeberSpec Acoustic Below Floor

Fibre-reinforced, rapid drying, self-smoothing, acoustic floor system. Manufactured in accordance with BS EN 13813: 2002. Complies with BS 8204-7. Not for use with underfloor heating.

Can be used to fulfil Robust Details floor solutions:

• E-FC-5, E-FC-11, E-FC-4, E-FC-11, E-FC-12 and E-FC-15, comprising a resilient layer directly applied to precast slab at 150 mm (minimum) with a density of 300 kg/m³ (minimum).
• E-FC-18, comprising a resilient layer directly applied to in-situ concrete slab at 225 mm (minimum) with a density of 2400 kg/m³ (minimum).

Components:

- Primer/ Bonding coat (weberfloor 4716 primer):

• Styrene acrylate dispersion which can be diluted with water. Designed for pre-treating all substrates prior to the application of weberfloor products.
• Regulates the porosity of the substrate.
• Improves the adhesion and flow of flooring products.
• Reduces the formation of pinholes in the levelling layer.

- Resilient layer:

• For use over resilient layer: Icopal-MONARFLOOR TRANQUILT, Cellecta YELOfon HD10+, Thermal Economics Isorubber Base, Thermal Economics Isorubber HP3 layer, Regupol Quietlay, TekRubber, InstaCoustic InstaLay 65 or Regupol Quietlay.

- Mesh reinforcement (weberfloor 4945 - not for use with underfloor heating):

• Glass fibre reinforcement net with an alkaline ­resistant impregnation.
• Specifically for use on weak substrates or in case the screed is laid non­-bonded.
• Reinforces weberfloor base and renovation screeds in floating floor applications.

- Base screed (weberfloor base rapid 4360):

• Rapid drying self-smoothing thick base screed.
• Minimum 40 mm thickness (capable to meeting acoustic requirements).
• Incorporates Low Dust Technology™, which provides a strong base layer for receiving tiles or a thin topping screed, and reduces the amount of waste and airborne dust produced during application.
• Can be pump or hand applied.
• Rapid drying, allowing an early overlay when compared to traditional sand/ cement or concrete screeds.
• Low alkalinity.
• Casein-free.
• For use over resilient layer: Icopal-MONARFLOOR TRANQUILT, Cellecta YELOfon HD10+, Thermal Economics Isorubber Base, Thermal Economics Isorubber HP3 layer, Regupol Quietlay, TekRubber, InstaCoustic InstaLay 65 or Regupol Quietlay.

- Top layer topping screed (weberfloor smooth rapid 4160):

• Pre-application of weberfloor 4716 primer required.
• Rapid drying self-smoothing thin topping screed.
• Can be pump or hand applied.
• Good spreading and smoothing characteristics.

Weber will only guarantee the products which form the system. Where membranes/ DPM by others are used, these will require a guarantee by the membrane/ DPM manufacturer.

Please ensure movement joints coincide with the building and can be used to assist with sequencing of application.

Preparation/ Recommendations:

• The substrate should be clean, free from dust, grease and other impurities that might prevent adhesion. All damaged and friable material should be removed. Leaving a good sound, solid substrate, this remedial work should then be a minimum 20 mm deep from the existing datum and 200 mm in length and width. This 200 mm should encapsulate the damaged area by a minimum of 50 mm. Should the damaged area be greater than 200 mm the excavation should always be a minimum of 50 mm past the furthest point.
• Prior to the final floor finish being applied, please ensure the weberfloor is suitably protected once cured.
• Reaction to fire clarification has not been determined/ tested and therefore this product is not suitable to be left exposed. For further details, please refer to table ZA.1.1 (page 22) of BS EN 13813 and contact Weber technical team. Prior to installation of Weber floor products, please consult with your local building control authority or equivalent to ensure a reaction to fire classification is not required - especially for onerous areas such as protected shafts, fire exits and fire corridors.
• In compliance with Scotland Technical Handbook (section 2 – 2.2.6 Combustibility), this product should not be used to domestic buildings that does exceed 18 m in storey height when installed onto a separating floor,. Please refer to the Scotland Technical Handbooks for further information.

Please note that weberfloor fibre 4360 and 4160 should not be painted or used without a floor finish.

Consult manufacturer's literature for specific mixing instructions.