Bauder Total Green Roof System Reinforced Bitumen Membrane Warm Roof Covering System - Torch Applied.

As 'Horizontal work'.

Bauder Super AL-E.

Guidance for specification option:

A robust, torch-applied, styrene-butadiene-styrene (SBS) elastomeric bitumen air and vapour control layer, featuring a tear-resistant aluminium foil lining for vapour impermeability. Once installed, the product provides a temporary waterproofing layer, allowing internal works to be carried out immediately.

• Width: 1 m.
• Length: 7.5 m.
• Thickness: 3.5 mm.
• Surface finish: top: mica; bottom: thermofusible polyethylene.
• Weight: 4.5 kg/m².
• Reinforcement: polyester-coated aluminium foil and 60 g/m² glass fleece.
• Tensile strength: ≥400 N/50mm (length and diagonal).
• Heat stability: +70°C.
• Cold bending test: -20°C.
• Elongation at break: ≥2% (length and diagonal).

Torch applied.

BauderGLAS Flatboard.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge.

Suitable for projects that require a high level of compressive strength and/ or to be non-combustible.

• Type: Cellular glass flatboard insulation board.
• Facing: Glass tissue or none-faced (depending upon system).
• Density: 100 kg/m³.
• Board size: Contact manufacturer for options.
• Thickness: 50 mm, 60 mm, 70 mm, 80 mm, 90 mm, 100 mm, 110 mm, 120 mm, 130 mm, 140 mm, 150 mm, 170 mm, 180 mm.
• Thermal conductivity: 0.036 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: 0.5 N/mm².

BauderGLAS Tapered.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge.

Suitable for projects that require a high level of compressive strength and/ or to be non-combustible.

• Type: Cellular glass tapered insulation board.
• Facing: Glass tissue or none-faced (depending upon system).
• Density: 100 kg/m³.
• Board size: Contact manufacturer for options.
• Thickness (maximum): 50 mm, 60 mm, 70 mm, 80 mm, 90 mm, 100 mm, 110 mm, 120 mm, 130 mm, 140 mm, 150 mm, 170 mm, 180 mm.
• Thermal conductivity: 0.036 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: 0.5 N/mm².

BauderROCK Flatboard.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge or mechanically fixed.

Mineral fibre insulation, suitable for projects that require a high level of sound reduction and/ or to be non-combustible; it has a zero GWP and ODP rating.

• Type: Dual density mineral wool flatboard.
• Facing: Top: 300 g/m² glass fibre fleece; bottom: unfaced.
• Density: 160 kg/m³.
• Board size: 1200 x 1000 mm.
• Board thickness (Flatboard): 60 mm, 85 mm, 105 mm, 115 mm, 150 mm, 185 mm (also available in tapered).
• Thermal conductivity: 0.039 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: >0.12 N/mm² (minimum 0.08 N/mm²).

BauderROCK Tapered.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge or mechanically fixed.

Mineral fibre insulation, suitable for projects that require a high level of sound reduction and/ or to be non-combustible; it has a zero GWP and ODP rating.

• Type: Tapered insulation board.
• Facing: Top: 300 g/m² glass fibre fleece; bottom: unfaced.
• Density: 160 kg/m³.
• Board size: 1200 x 1000 mm.
• Board thickness (Flatboard): 60 mm, 85 mm, 105 mm, 115 mm, 150 mm, 185 mm (also available in tapered).
• Thermal conductivity: 0.039 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: >0.12 N/mm² (minimum 0.08 N/mm²).

PU Insulation Adhesive – Tin.

Guidance for specification option:

Not for foil to foil applications (e.g. FA-TE to FA-TE).

PU Insulation Adhesive – Twin cartridge.

BauderFLEX G4E.

Guidance for specification option:

A 4 mm, heavy-duty, torch-applied elastomeric bitumen underlayer with a strong woven glass reinforcement to provide an extremely high tensile strength.

• Width: 1 m.
• Length: 7.5 m.
• Thickness: 4 mm.
• Surface finish: Top: mica; bottom: thermofusible polyethylene.
• Weight: 4.8 kg/m².
• Tensile strength: ≥1200 N/50mm (length and diagonal).
• Heat stability: +110°C.
• Cold bending test: -30°C.
• Elongation at break: ≥2% (length and diagonal).

Torch applied.

PLANT E.

Guidance for specification option:

A high quality, heavy duty, torch-applied, elastomeric bitumen capping sheet. The product features chemically treated bitumen to deliver superior root resistance which has been tested and approved by the FLL. The membrane is reinforced with 250 g/m² spunbond polyester fleece to allow the finished product to cope with structural movement without fracture. Expandable graphite fire retardant is also incorporated to reduce spread of flame.

• Width: 1 m.
• Length: 5 m.
• Thickness: 5.2 mm.
• Weight: 6 kg/m².
• Surface: Top: Green slate mineral chippings; Bottom: Thermofusible polyethylene.
• Reinforcement: 250 g/m² recycled spunbond polyester.
• Cold bending test: -36°C.
• Softening point: >120°C.
• Tensile strength: Length >1000 N/50 mm; transverse >1000 N/50mm.
• Elongation at break: Length >45%; transverse >45%.

Torch applied.

Not required.

Bauder GRP Trim.

Guidance for specification option:

GRP roof edge trim for use with Bauder bituminous roof systems. Available in colours of either grey or black, and a choice of profiles to suit the requirements of most projects. Consult manufacturer literature and insert requirements.

Bauder GRP Water Check Trim.

Guidance for specification option:

GRP water check trim to be used on parapets and perimeter kerbs wider than 200 mm – must not be used on its own as a check kerb. Available in black only.

Bauder Aluminium Termination Bar.

Guidance for specification option:

Natural finish aluminium alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall.

Bauder GRP Termination Bar.

Guidance for specification option:

Black glass reinforced plastic (GRP) alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall.

Not required.

Bauder LiquiFIBRE Detailing Kit.

Guidance for specification option:

Fast-curing waterproofing resin, containing fibre reinforcement that can be used for detailing awkward shapes or inaccessible areas where using LiquiDETAIL is impractical. PMMA-based resin that requires a catalyst and is solvent, isocyanate and halogen-free.

Bauder LiquiDETAIL.

Guidance for specification option:

Cold liquid applied fast curing waterproofing resin that can be used on upstands and details. PMMA-based resin that requires the addition of catalyst to trigger curing and is solvent, isocyanate and halogen free.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Not required.

Landscaping options.

Guidance for specification option:

Please refer to Bauder Extensive / Biodiverse / Intensive Landscaping systems.

Not required.

Bauder lightning conductors.

Guidance for specification option:

Lightning conductor clips are a specially designed secure clip that allows for movement.

• Bauder Lightning conductor – Type 4: Polyvinyl chloride (PVC) coated or bare conductor.

Bauder rainwater outlets.

Guidance for specification option:

Bauder has a range of insulated or stainless-steel rainwater outlets.

The insulated outlets can be used for maintaining thermal continuity at drainage points. Suitable for warm, cold and inverted roof construction, the high thermal value of the rigid foam body prevents condensation from forming on the underside of the outlet.

Designed for use when connecting to conventional drainage systems, with excellent flow rate performance and is suitable for both new build and refurbishment projects. Outlets are included in the Bauder waterproofing system guarantee as they are integrated components.

Flow rate figures (where applicable) are based on BS EN 12056:3:2000, typically taken using a 35 mm header of water including leaf grille:

• Bauder Bitumen Compact Vertical Outlet DN100: Insulated internal outlet, 6.1 L/s.
• Bauder Bitumen Vertical Outlet DN70: Insulated internal outlet, 7.1 L/s.
• Bauder Bitumen Vertical Outlet DN150: Insulated internal outlet, 7.2 L/s.
• Bauder Bitumen Letterbox Parapet Outlet DN 205 including stainless-steel leaf guard, 2.02 L/s.
• Bauder Bitumen Parapet Outlet DN 100 including stainless-steel leaf guard, 1.06 L/s.
• Bauder Bitumen Vertical Refurb Outlet DN70, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Vertical Refurb Outlet DN95, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Vertical Refurb Outlet DN145, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.

Bauder rooflights/ glazing/ ventilation.

Guidance for specification option:

All these glazing products are fully compatible with the roof waterproofing systems. Consult manufacturer for details and insert requirements.

• BauderDOME Rooflight.
• Bauder Euroglaze Rooflight.
• Bauder Special Modular Rooflight.
• Bauder Continuous Rooflight.
• Bauder Walk-on Rooflight.
• Bauder Direct Glazing.
• Bauder AOV.
• Bauder Modular Link Glazing.
• Bauder Structural Rooflight.
• Bauder Fire Rated Rooflight.