Compare

Knauf Performer: PC-50-055-6-1-15-MP-25

Name: Knauf Performer: PC-50-055-6-1-15-MP-25
Brand: Knauf UK
SKU: 8f3Fphzd5KLnP2QUKAC9Zp

Verified by manufacturer 3 months ago

With deflection head arrangement

Knauf UK

Third party certifications:

EPD
Certificate type
CCPI System
Certificate type

The Knauf Performer system is Knauf's most versatile and commonly used partition system.

Jump to:

0800 521 050 Website

Application

Plasterboard partition system.

Description

The Knauf Performer system is Knauf's most versatile and commonly used partition system. It is constructed using a single row of Knauf metal studs with Knauf plasterboards to both sides in order to meet fire, acoustic, moisture and impact requirements.

The Performer system is lightweight, simple to construct and should be used in conjunction with Knauf’s finishing solutions range.

General information

Material	Gypsum Metal Glass mineral wool
Shape	Rectangle Other Square
Width	Bespoke
Height	Bespoke

Uniclass	Ss_25_10_30_35 Gypsum board partition systemsPrimary
CAWS	K10/30 Metal stud K10/125 Metal stud partition system

Specification data - Gypsum board partition systems

Framing	Knauf 50 'C' (0.55) at 600 mm centres to suit maximum height. Head channel: Knauf 52 Deep Flange 'U' Channel (0.70) (70 mm deep flange). Floor channel: Knauf 52 'U' Channel (0.55).
Insulation	25 mm Knauf Insulation Acoustic Roll.
Linings	1 x 15 mm Knauf Moisture Panel to each side.
Fasteners	25 mm Knauf Drywall screws - self tapping.
Joint treatment	Horizontal joint: Knauf Flat Fixing Plate.
Finish	For paint finishes: System must be taped and jointed using Knauf Joint Filler (Premium) or Knauf Joint Cement Premium and Knauf Joint Tape (Paper). Or alternative Knauf jointing compounds manufactured to EN 13963. Knauf Wallboard Primer applied once taping and jointing completed. Prior to where paint decoration is required. For preparation for decoration of where gypsum plaster skim is required, the outer layer of plasterboard joints is required to be taped and filled, using Knauf Joint Filler (Premium) and Knauf Joint Tape (Paper) meeting quality level 1 in accordance with Eurogypsum - Drywall Jointing & Finishing - Surface quality level classification. For application where gypsum skim finish is required, the Knauf system is to be taped and filled using Knauf jointing compounds. When using Knauf Performance Plus, the applicator of gypsum skim finish is required to check if pre-treatment is required.
Execution	Consult manufacturer's literature at https://www.knauf.co.uk/our-services/resources

Deflection head	For deflection head allowance of up to -25 mm or ±12.5 mm: use 2 x 19 mm Knauf Coreboard fillet.
Fire resistance	N/A.
Sound insulation	42 dB (Rw) when tested to BS EN 10140-2.
Duty rating (to BS 5234-2)	Heavy Duty in accordance with BS 5234-2, clause 1.6.2 & 1.6.3 of Annex B & C.
System code	EN-PC-50-055-6-1-15-MP-25. Guidance for specification option: The maximum height stated under Partition height (see below) is for the fire resistance of the system to meet project requirements where EN compliance is required. The stated maximum height figure is the lower value between the cold state height, calculated structurally to a limiting deflection of L/240 @ 200 Pa and the fire state height, as outlined in accordance with EN 1364-1 and EN 15254-3. BS-PC-50-055-6-1-15-MP-25. Guidance for specification option: The maximum height stated under Partition height (see below) is for the fire resistance of the system to meet project requirements where BS compliance (BS 476-22), is required and is accepted by the client, designers and building control. The stated maximum height figure is based on the maximum cold state height, calculated structurally to a limiting deflection of L/240 @ 200 Pa.
Partition height	- Manufacturer guidance Insert requirements, maximum 3100 mm. See System code for further details.
Partition thickness	82 mm. Manufacturer guidance Excluding finishes.

Sustainability data

Country of material origin	Spain Manufacturer guidance Applies to our natural gypsum only which is the main component of plasterboard. Other components are from other countries. Please contact Knauf for more details.
Country of product manufacture	United Kingdom Manufacturer guidance UK applies to the majority of manufacture but a small percentage of finished items may be imported. Please contact Knauf for more details.
Material	Gypsum Metal Glass mineral wool
Embodied carbon A1-A3 (production stage) as defined in BS EN 15804	- Manufacturer guidance Individual product EPDs for plasterboard and metal components available at: https://www.knauf.co.uk/our-services/resources/environmental-product-declarations-1
Recyclability	Individual product EPDs for plasterboard and metal components available at: https://www.knauf.co.uk/our-services/resources/environmental-product-declarations-2
Recycled content As defined in clause 7.8 of BS EN ISO 14021	11.9 % Manufacturer guidance (2023 average by mass for all UK produced plasterboards, recycled gypsum & paper)