NBS Source
List your products

DELTA® PT - Original Waterproof Membrane System

Third party certifications:
  • BBA Agrément Certificate

    Certificate type

Delta Membrane Systems Ltd

A dimpled membrane, providing a key for plaster, render or dab fixed plasterboard.

Jump to:
+44 (0)1992 523523 www.deltamembranes.com
Application

  • Mesh is welded to the front face of the membrane to allow plasters and renders to be applied.
  • Studs isolate the wall from the new plaster and allow ventilation of the wall for permanent dampness control.
  • Ventilation is achieved with the use of an external air vent or with the use of Delta-PT Profiles fixed at the upper and lower edges of the wall. The profile has ventilation slots provided.
  • Delta-PT can be used as part of a sealed waterproofing application, on walls, vaults, and archways where a plastered or rendered finish is required or when a specific key is needed. It can also be used externally as a waterproof support for rendered finishes.
  • All joints and fixings must be sealed using Delta sealants.
  • Sheets must be fixed along all edges and generally at not more than 250 mm vertical and horizontal staggered centres using Delta-PT Fixing Plugs and Delta Sealant or grommet. Alternatively, use the Delta-Qwik-Seal Plug. When used externally, fixing centres must be closed up to 150 mm.

Description

A dimpled membrane with a mesh face, providing a key for plaster, render or dab fixed plasterboard.

Features:

  • A high performance polyethylene membrane for use on damp and/ or contaminated walls, above and below ground, vaults and basements.
  • Delta-PT is extruded into a series of studs to create a continuous air gap behind the waterproof membrane.

Application:

  • Mesh is welded to the front face of the membrane to allow plasters and renders to be applied.
  • Studs isolate the wall from the new plaster and allow ventilation of the wall for permanent dampness control.
  • Ventilation is achieved with the use of an external air vent or with the use of Delta-PT Profiles fixed at the upper and lower edges of the wall. The profile has ventilation slots provided.
  • Delta-PT can be used as part of a sealed waterproofing application, on walls, vaults, and archways where a plastered or rendered finish is required or when a specific key is needed. It can also be used externally as a waterproof support for rendered finishes.
  • All joints and fixings must be sealed using Delta sealants.
  • Sheets must be fixed along all edges and generally at not more than 250 mm vertical and horizontal staggered centres using Delta-PT Fixing Plugs and Delta Sealant or grommet. Alternatively, use the Delta-Qwik-Seal Plug. When used externally, fixing centres must be closed up to 150 mm.

Plastering:

The membrane should be plastered with either 'Whitewall' plaster or Carlite Bonding.

External rendering:

  • Where the membrane is to be used externally it must be rendered with a cement-lime-sand (1:1:6) render applied in three coats to a total thickness of 20 mm.
  • Due to the difference in thermal characteristics between Delta-PT and the render, expansion joints through the render to the membrane must be trowelled in along each lap joint to reduce the possibility of cracking. These joints must be filled with a suitable flexible polymer-based sealant.
  • Alternatively, a polymer/fibre modified render can be used and should be applied in two coats. This render is polymer/ fibre modified, and eliminates the need for extensive expansion joints, other than what is required to meet the Building Regulations.
  • A 5 mm ventilation gap at the top, and at least 10 mm at the bottom should be left to assist the ventilation of the air-gap behind the Delta-PT membrane. Delta-PT profile is secured to the membrane and substrate to maintain these gaps.

Dry lining:

  • A Bonding plaster to BS 1191-2, Type A3, is applied in vertical strips over the fixing centres and in bands along the top and bottom of the membrane. The plaster dabs are applied to a minimum thickness of 8 mm, and should cover a minimum of 50% of the membrane.
  • Gypsum plasterboard to BS 1230-1,or similar drylining boards covered by Agrément Certificate, are pressed onto the plaster dabs and jointed in the usual manner.

Decoration:

Once the plastered, dry-lined or rendered surface has dried, the surface can be painted or wallpapered using traditional methods and materials.

General information
Material

High density polyethylene

Uniclass 2015
Damp-proof lathings (Pr_20_85_46_21)Primary
Specification data - Damp-proof lathings
Product Reference

Delta-PT

Accessories

Delta-PT Fixing Plugs

Delta-PT Lath Plugs with grommet

Delta-PT Profiles

Delta Sealant

Delta-Qwik-Seal Plug

Plastic percussion plug with waterproof grommet for concrete or masonry.

Flexidri Plus plugs

Expanding waterproof plug with waterproof grommet.

Flexidri plugs

Standard product features

Thickness (approximately):

0.5 mm.

Stud height (approximately):

8 mm.

Roll size:

1500 or 2000 mm.

Compressive strength (approximately):

70 kN/m².

Drainage capacity (approximately):

5 L/s per m.

Digital objects
PlatformCompatibleVersionCertified to
ARCHICAD
- 1.0
AECOsim
- 1.0
Vectorworks
- 1.0
Revit
Revit 2016 7 2.0
IFC
IFC2X3 4 1.3
Download now from NBS National BIM Library
Third party certifications
Similar products from Delta Membrane Systems Ltd