Cold Applied Liquid for Roofs, Balconies & Terraces - IKO Metatech
Verified by manufacturer 7 months ago
Two-component polymethyl methacrylate (PMMA)-based waterproofing resin system.
Application
IKO metatech is used as fully reinforced waterproofing resin in the
following liquid waterproofing systems:
- IKO metatech Roof.
- IKO metatech Balcony.
- IKO metatech Car Park.
Description
A two-component coating based on methacrylates that cures after the hardener powder has been incorporated. Apart from fast curing (after only 45 minutes), it is also characterized by rapid installation, as the second layer is applied wet-on-wet to the first layer.
ETA-15/0478 certificate (European Technical Assessment) according to ETAG005. CE Marked.
Features and benefits:
- Two-component: extremely fast installation and drying.
- Sustainable PMMA technology.
- Installation possible under poor weather conditions.
- Viscous: does not drip down when applied vertically.
- IKO guarantee up to 25 years.
- Approved contractor and installer application.
- Consumption rate of min 3 kg/m².
General information
Color | Grey |
Material | Polymethyl methacrylate (PMMA) |
Length | Bespoke |
Width | Bespoke |
Uniclass | |
CAWS | J31/12 Inverted roof coating J31/130 Inverted roof coating |
Specification data - Liquid-applied inverted roof covering systems
Preparation | - |
Horizontal work | IKO metatech porous surface primer.IKO metatech non porous surface primer. |
Skirtings and vertical work | IKO metatech porous surface primer.IKO metatech non porous surface primer. |
Carrier membrane | - |
Type | IKO Systems H-A underlays are polyester reinforced bitumen membranes used as underlays within a built up roofing system, The membranes are coated on both sides with self-adhesive bitumen SBS elastomeric coating. They have a fine mineral upper surface with a 75 mm release film selvedge to facilitate rapid installation of lap joints. Size: 1 x 16 m. |
Liquid-applied waterproofing | - |
Type | IKO metatech waterproofing.A two-component coating based on methacrylates that cures after the hardener powder has been incorporated. Apart from fast curing (after only 45 minutes), IKO metatech Detail is also characterised by rapid installation, as the second layer is applied wet-on-wet to the first layer. |
Reinforcement | IKO Protection Fleece.A reinforcement fleece consisting of non-woven polyester with a density of 110 g/m². This fleece is rolled out in the wet first layer of IKO metatech Detail and pressed in areas that are subject to heavy footfall. It therefore ensures the strength, stability and longevity of the system. |
Insulation | - |
Type | IKO enertherm XPS insulation, 600 x 1250 mm.IKO enertherm XPS is a light orange rigid extruded polystyrene (XPS) board with a Global Warming Potential (GWP) of less than five. A lightweight, lap jointed board with high compressive strength and performance. Thermal performance of an inverted roof is improved when used in conjunction with IKO enertherm WCL. Used for the thermal insulation of a wide variety of flat roofs including an inverted roof below ballast or paving slabs or a green/garden roof. BBA certified 17/5467. Thickness: 50, 70, 100, 130, 160, 180, 200, 220 mm available, consult literature and insert requirements. |
Water control layer | IKO enertherm WCL (Water control layer). |
Ballast | IKO Paving supports and 50 mm paving.50 mm ballast. |
Colour | Stone grey, RAL 7043. Pebble grey RAL 7032. |
Density | +/- 1,22 g/cm³. This relates to the IKO Metatech coating. |
Hardness | +/- 62 (Shore A 23°C). This relates to the IKO Metatech coating. |
TensileStrength | +/- 4,5 N/mm². This relates to the IKO Metatech coating. |
Elongation | +/- 240%. This relates to the IKO Metatech coating. |
Viscosity | +/- 17 dPas (25°C, 20 rpm, spindle3). This relates to the IKO Metatech coating. |
Curing timeThis relates to the IKO Metatech coating. | Pot life: +/- 15 min. Rain proof: +/- 30 min. Can be walked on: +/- 45 min. Fully cured: +/- 2 h. |
Storage | 12 months in the hermetically sealed packaging, when stored in a dry, cool and frost-free place. Keep the edges of the tin clean. When closing the tin, place the lid and the lever lock ring in the correct way and remove any product that might remain on the tin. |
Standards | To ISO 9001, ISO 14001. |
Literature
IKO Flexia - Cold Applied Liquid for Roofs, Balconies & Car Parks
Case studies
Fast Liquid Waterproofing Solution for Flat Roofs
IKO Polimar CRS used for Trimpley Water Treatment
Liquid and Bituminous Multi-System Project - Airbus, Stevenage
Liquid Waterproofing Solution Meets Refurbishment Needs of Coastal Residential Development
Liquid Waterproofing to Save an Underground Car Park
Refurbishment of 1960's Flats Using Liquid Waterproofing
New-Build Retirement Block Receives the Benefits of both a Hot Melt, Bituminous and Cold Applied Liquid Roofing Systems