NBS Source
List your products
IPP Ltd

IPP Ltd

Insulation and Non-Combustible Fire Protection Boards for Timber Frame, Light Gauge Steel Frame.

+44 (0)1621 776252 www.intpetro.com/

Sort by:

Showing 1-21 of 21

Magply Euroclass A1 Non-Combustible Fire Protection Board (various thicknesses)

Magply Euroclass A1 Non-Combustible Fire Protection Board (various thicknesses)

IPP Ltd

When fixing Magply, screws should have a thread the whole length of the shank (to the tip) for maximum strength and resistance. Specialist details are available. For Fire Resistant Applications useeither Magply 4 Hour Intumescent Sealant or Magply A1 Filler Adhesive. The length of fixings and centres depends upon national regulations and applications. As a guide the fixing should be a minimum of 28mm into the timber stud plus the thickness of the board. For standard drywall applications, use a galvanised or phosphate coated fixing along with standard jointing and taping.
Magply Non-Combustible Board BDA Agrement BAW 18-086/01/A

Magply Non-Combustible Board BDA Agrement BAW 18-086/01/A

IPP Ltd

Magply is intended to be used in self-supporting composite lightweight panels and spandrel panels for external and internal walls, cladding and ceilings. The panels can contribute to the loadbearing capacity of hte works. Structural Performance : When fully installed in the building structure in accordance with this agrement the Product can contribute to adequate strength and stiffness to resist the wind and imposed loads likely to be experienced in the UK. Safety in case of Fire : Reaction to Fire - the product is classified as Euroclass A1 (Non-combustible) in accordance with BS EN 13501-1. Durability and Maintenance : The dimensional stability of hte product panels is extremely good. Fire Resistance - The following loadbearing Product panel assembly has been tested to BS 1365-1
Magply Plasterbond Datasheet

Magply Plasterbond Datasheet

IPP Ltd

MAGPLY PLASTER BOND is a mineral based plaster primer which is designed to control high suction backgrounds on Magply MGO boards whilst still remaining vapour open. The primers fine gritted surface provides a key for a new suitable plaster to bond to. MAGPLY PLASTER BOND is in-dependently tested by audited facilities Sheffield Hallam University and PRA coatings, for vapour diffusion to reassure you that water vapour is not trapped in the fabric of your building. No VOC, no odour, water-based and certified as vapour permeable. Our natural mineral and wa-ter-glass primer free from any other cobinders such as solvents, gypsum and cement and is non-hazardous. MAGPLY PLASTER BOND plaster primer is available in 17kg UN certified containers.
Magply Recovery Board

Magply Recovery Board

IPP Ltd

Magply Recovery /Protection Board Magply recovery and protection boards have been developed to meet the roofing industry need for a cost-effective, lightweight and fireproof board that will provide an inert and stable separating layer for all types of waterproofing overlay applications. It can also be used as a tough, durable and reusable protection layer over competed installations. Available in both 3mm and 6mm thicknesses, to suit both light and heavy traffic applications, the board can be easily cut to fit around penetrations and at abutments and can either be mechanically fixed or bonded into position when used in overlay applications.
Render Carrier Board

Render Carrier Board

IPP Ltd

Magply is designed for direct render applications to form the external façades of commercial and domestic properties which utilise hybrid frames structures. Magply 12mm Board offers the perfect substrate for use with thin proprietary render systems on to Timber or Light Gauge Steel Frames. Magply is a high strength, breathable board manufactured from MgSO4 and reinforcement meshes which provide excellent dimensional stability. Magply is A1 Non-Combustible and has been tested with a variety of render systems by the British Board of Agrément.

Showing 1-21 of 21