You are viewing content for United Kingdom.
Choose a country to see content for your location. Changing region will navigate you to the homepage.
Compare variants
Summary
Type 2+3 SPD’s from Acti9 Isobar P and KQ load centre product range.
-
-
Application
The iPRD range shall be suitable for installation on two types of fishbone type distribution boards according to the international standard EN 60715 and DIN43880 1988.
The SPD shall be able to fit on Acti9 Isobar-P distribution boards, or into one Acti9 KQ load centres.
- On a 5-wire system TN-S or TN-C-S – L1, L2, L3, N and PE (including single phase).
- On a 4-wire system TT net – L1, L2, L3, N (including single phase).
- SPD shall fit into any fishbone system of the cabinet without causing any damage to other devices or their accessories.
-
-
Description
The iPRD range shall be a surge protection device:
- The SPD shall be defined to be in conformity with the IEC 61643-11:2011, EN 61643- 11:2012+A11:2018 standard.
- The SPD shall be suitable for installation on DIN rail according to the international standard EN 60715.
- The SPD shall be suitable for installation on fishbone panel boards
- The SPD shall be containing visual fault indicator with remote signalling contact.
- The SPD shall be delivered with removable cartridges for line protection.
The iPRD range shall include products with added functions to offer simplification of installation inside the cabinet and remote supervision of the product end of life.
- End of life Remote supervision:
- SPD iPRD shall have a Potential-free O/C contacts to inform owner of SPD end of life through remote supervision like SE Wiser solution or KNX functionality.
- For KQ load center SPD, the product will be designed with a variant without potential-free O/C contacts.
General rules for SPD :
- IEC 61643-11 ed1 (2011-03).
- EN 61643-11 (2012-10) +A1: 2014 + A11:2018.
- BS EN 61643-11:2012+A11:2018 : Surge protective devices connected to low-voltage power systems. Requirements and test methods.
- BS 7671:2018+A3:2024 : Requirements for Electrical Installations. IET Wiring Regulations.
Products should conform to following Additional Related Standards – standards not necessarily directly applicable to the product itself but which need to be considered during the development program either in part or in total includes:
- IEC 60529 (1989)+ A1 (1999) + A2 (2013).
- Degrees of protection by enclosures.
- BS EN 61439-3:2012 Low-voltage switchgear and control gear assemblies Distribution boards intended to be operated by ordinary persons (DBO).
- 2D design tolerances compliant with ISO 8015.
CE and UKCA marked. Meets the requirements of LV Directives: 2014/35/EU.
-
-
Color
White
-
-
Material
Plastic
-
-
Shape
Rectangle
-
-
Specification
Classification data
Standard
To BS EN 61643-11, Type 2 + Type 3.
-
-
Operating voltage and frequency (nominal)
230 V.
-
-
Number of poles
3PN.
-
-
Maximum continuous operating voltage (Uc)
340V / 260V.
-
-
Mode of protection
L/N protection: MOV technology.
N/PE protection: GDT technology.
-
-
Nominal discharge current (In)
20 kA per mode.
-
-
Maximum discharge current 8/20 µs (Imax)
40 kA per mode.
-
-
Minimum short circuit current rating (Isccr)
25 kA stand alone and installed in Fishbone panelboard (tested at 50 kA in lab not a scope of VDE CB).
-
-
Voltage protection level (Up)
1500 V.
-
-
Open circuit voltage (Uoc)
6 kV.
-
-
Protection status indicators
Green indicating full protection status.
Red indicating no protection – failure of device.
-
-
Remote monitoring
Required (Available with Acti9)., None.
-
-
Ingress protection (minimum)
To BS EN 60529, IP40 (device in panel board).
IP 20 (Device wired and cartridge removed).
-
-
Mounting method
The SPD shall be suitable for installation on DIN rail according to the international standard EN 60715. Both designed exclusively to be mounted on Acti9 Isobar P and/or KQ Loadcentre boards.
-
-
Sustainability data
Material
Plastic
-
-
Expected Life
20 year
-
-