"side hung doors metal"

PREFACE One of the objectives of the Canadian Sheet Steel Building Institute is the development of product standards to promote sound construction using safe building practices. This Standard is intended to further this objective by providing to buyers, manufacturers and installers of steel farm roofing and siding, information which can be used or adopted by reference where desired. The requirements contained herein are in accordance with accepted engineering principles, augmented by experience. They include recommendations covering steel thicknesses, minimum metallic coating designations, as well as design, manufacture and installation in general.

Preface One of the objectives of the CSSBI and its members is the development of standards and technical publications that promote safety, performance and good practice. This "How To Series" of publications is an educational tool intended to give guidance to anyone specifying sheet steel building products. This particular publication is published as an aid to building owners as well as roofing and siding installers. It offers simple and practical recommendations for the selection, application and installation of light gauge steel cladding. This is a generic guide giving the basic details and should only supplement the specific recommendations or guidance published by the manufacturer appropriate to their own products. The views expressed in this guide are a collection of installation techniques and do not necessarily reflect those of all member companies of the CANADIAN SHEET STEEL BUILDING INSTITUTE. The material presented in this publication has been prepared for the general information of the reader. While the material is believed to be technically correct and in accordance with recognized good practice at the time of publication, it should not be used without first securing competent advice with respect to its suitability for any specific application. Neither the CANADIAN SHEET STEEL BUILDING INSTITUTE nor its Members warrant or assume liability for the suitability of this bulletin for any general or particular application.

Buildings consume one-third of all energy and two-thirds of all electricity generated. Cool metal roofs can help reduce energy consumption by lowering cooling loads with their wide array of finishes, designs and colors.Cool metal roofs are energy-efficient. • The roof can have the greatest impact on the energy use of a building. On a typical summer afternoon, a light-colored, more reflective roof that reflects 80 percent of sunlight will stay about 310C (550F) cooler than a darker roof that reflects only 20 percent of sunlight, as reported by the Heat Island Group of the Lawrence Berkeley National Laboratory. • Cool metal roofs are an excellent option for commercial retrofit applications because they can be efficiently installed with above-sheathing ventilation, allowing heat to dissipate through the ridge vent in hot weather while acting as an insulating layer when it is cold. Metal roofs can result in as much as a 30 percent reduction in heat gain through the vented roof. • Metal roofs provide the optimal foundation for photovoltaic installations since the roof can be expected to last longer than the PV system it supports. • Wall and roof solar heat recovery systems can be integrated with steel cladding and used to provide air, water or process heating needs. • Cool metal roofing is available unpainted, with thermosetting coil-applied paint finishes, or with granular-coated surfaces. This family of roofing can achieve solar reflectance of over 70 percent, meeting the EPA Energy Star Roof Products Program performance criteria. • Emittance as high as 90 percent can be achieved for painted and granular-coated metal roofing. • Painted metal roofs retain 95 percent of their initial reflectance and emittance over time. They resist the growth of organic matter and shed dirt more readily than other materials. • Cool metal roofing can help to mitigate the Urban Heat Island Effect because of its high reflectance, which can reduce ambient air temperatures. Cool metal roofs are cost-effective. • Metal roofing has low life-cycle costs, making it the choice of many school, government, commercial, industrial and institutional building owners. • Due to its light weight per unit area, structural savings can be realized in a building when compared with heavier non-metal roofing alternatives. • For re-roofing projects, metal roofing can often be applied over the original roof, saving removal and disposal costs. • Metal roofing is fully recyclable when ultimately removed as part of building renovation or demolition, allowing it to credibly claim both recycled content and 100 percent recyclability by recognized definitions. The product’s recyclability also provides significant savings on construction removal and disposal costs.

Introduction Sheet steel roofing and siding (cladding) is available in a wide variety of profiles, colours and paint systems. The modern prepainted systems used on Canadian-made products will provide decades of beautiful performance before there are any visible signs of deterioration of the paint surface. However, an important component of the cladding system is the fastener used to attach it to the structure. This fastener is not simply a screw; it is part of the roof or wall assembly and should be expected to provide the same long-term performance. This performance is not simply the capacity to safely hold the cladding in place, but also to match the colour and durability of the paint system. The selection of the correct screw for the job is the first step in the creation of a cladding system that will provide long-term performance. The next step is the installation. Installing screws in sheet steel cladding is commonplace and can be done very efficiently. The tool manufacturers have developed a wide range of options for installing fasteners into any type of substrate. Selecting the most appropriate tool will help the installation process.

Architects and Specification Writers are increasingly selecting unpainted metallic coated steels for architectural roofing and cladding applications on building exteriors where they want a “Silver” metallic finish. This is occurring more frequently, and even on “prestige” type projects. The Canadian Sheet Steel Building Institute whose fabricator members manufacture a wide variety of building panel profiles for roofing and cladding applications, are being asked to supply unpainted (natural finish) galvanized or resin coated 55% Aluminum-Zinc coated steel for these architecturally exposed end uses. Oftentimes, these materials are specified because the designer finds the natural finish of these products very appealing and sometimes because of material cost savings opportunities. This Fact Sheet has been developed to provide guidance in material selection and provide information on the Architectural Metallic Finishes that are available for highly visible steep slope roofing and cladding applications. 

What is Oil-Canning? Oil-canning is associated with all thin sheet metal products and occurs in the wide flat portions of the cladding profile. It is seen as a series of standing waves, or regular bumps and hollows alternating along the flat length of the panel. This waviness, when viewed under certain conditions, can be undesirable aesthetically and may not meet with the owner’s expectations. The CSSBI wants to help avoid this situation. The cladding manufacturers are aware of the potential for oil-canning in the cladding profiles and can help minimize the effect. It is important for the proper steps to be taken during manufacturing and installation to produce a quality finished product; therefore, specifiers should insist on product from a reliable, experienced cladding manufacturer, like a CSSBI member company. Quality control, however, cannot end on the shop floor. The building project needs the cooperation and knowledge of everyone involved to enhance the quality of the finished job. Oil-canning is a phenomenon that can be managed if the following factors are considered at the beginning of a project.

Introduction Prefinished sheet steel is used on many building products from wall cladding, to architectural roofing to interior panels. Prefinished sheet steel has been used in Canada for over 30 years and there may be sites were the paint surface is in need of repainting. This bulletin is intended to give some guidance on repainting prefinished panels. Due to the diversity of factory applied prefinished systems, and the diversity of potential field applied repaint systems, it is impossible to offer one comprehensive repaint procedure for all possible situations. However, it is possible to offer a set of guidelines to be considered in every potential situation.

It’s a fact that buildings consume two thirds of all the electricity produced in North America and one third of all the energy produced in North America. While it is recognized that adding insulation under the roof surface can reduce cooling and heating costs, there is a diminishing return on the strategy of increasing insulation to conserve energy costs. This is where “cool roofing” can play a role in further reducing the energy consumed, and in minimizing the Heat Island effect created in the big urban cities. Cool roofing relies on sustainable, energy efficient, coated steel products, in a wide variety of finishes, colours, textures and roofing profiles. It conserves energy through its properties of reflectivity and emissivity

The newly opened Exploratorium has brought energy and excitement to the city's bustling waterfront. EHDD transformed the historic Pier 15, built in 1915, to a 330,000 square foot indoor and outdoor campus, being touted as the largest net-zero building in the city and potentially the largest net-zero museum in the world. SAFTI FIRST® supplied a total of 19 pairs of 45-minute steel doors 11 pairs on north side and 8 pairs on the south side using SuperLite® II-XL 45 IGU in GPX® Builders Series Fire Protective.

Adaptive reuse, or the process of taking an old building or structure and repurposing it for something other than what it was originally designed for, has gained a lot traction with developers and architects alike – and for many good reasons. For one thing, it is more economical and sustainable to work with an existing structure than to demolish an old building, clean up the site, and rebuild with entirely new materials. It also helps preserve historical structures that add character to the community, as well as reduce urban sprawl. For the multifamily sector, we’ve seen adaptive reuse applied to old schools, government buildings, warehouses, etc. because these structures are usually centrally located in many downtown areas.

For BART's Doolittle Maintenance Facility at the new Oakland Airport connector, SAFTI FIRST® provided 60 minute, fire resistive wall openings in the exterior using SuperLite® II-XL 60 insulated with low-e glazing in GPX® Framing with a clear anodized finish. SAFTI FIRST® engineered a connection that allows the structural elements of the GPX® Architectural Series Framing System to support an integral sunshade system, instead of being hung in front of it. The Doolittle Bart Station is one of the first installations of the GPX® Architectural Series System with sunshade connections, which also include SLCC New Instruction and Administrative Building in Salt Lake City, UT.

Introduction Most cold formed steel building products, whether painted or unpainted, are manufactured from a sheet steel material that has some form of metallic coating applied. This metallic coating can be zinc (galvanized), zinc-iron alloy (galvanneal) or a 55% aluminum-zinc alloy (GalvalumeTM). The metallic coating is available in a range of thicknesses to provide the degree of corrosion protection and service life required. One of the concerns expressed by installers relates to the presence of wet storage staining on the products, how this staining impacts the long term performance, and what can be done to remove it. The purpose of this fact sheet is to address some of these issues, allay some fears, and give guidance on proper storage techniques.

1. SCOPE 1.1 The following specifications shall apply to hot-dipped metallic-coated sheet steel prefinished with colours of proven durability and suitable for exterior exposure as delivered from the coil coater. Proven paint systems for building products have been designed for vertical applications whose surfaces are no more than 30° to the vertical and non-vertical applications whose surfaces ranging from 5° up to 60° to the horizontal. It is not recommended for aggressive atmospheric exposure. 1.2 The prefinish system shall consist of a primer and topcoat continuously applied and cured within the paint manufacturer’s specifications on cleaned, pretreated, metallic-coated substrate. The pretreatment specified shall be zinc phosphate for galvanized steel and metal oxide pretreatment for aluminum-zinc alloy-coated steel, applied in accordance with the pretreatment manufacturer’s specifications.

Renovation stripping out the building completely and rebuilding the walls, Passive Purple® was applied in between the connections of the internal side of the external walls which were a combination of masonry, timber, and steel frame. The ground floor ceiling was removed exposing the warped old timber joists with cracks in the surrounding brickwork and mortar. This was given attention to detail using Passive Purple® Brush to seal above an airtight foam to guarantee the airtightness of this major air leak zone before the final spray coat of Passive Purple® airtight membrane was applied. Passive Purple® was also used to seal window and door linings, ready for the new triple glazed windows to go in. Passive Purple® was sprayed on all the walls and ceiling. This is an ongoing project that still is awaiting an air test, the client is looking to hit 2.5 ach and installing MVHR.

Four Key Components Constitute Prefinished Sheet Steel Prefinished sheet steel for construction consists of four major components: the sheet steel itself, a metallic (zinc or aluminum-zinc alloy) coating, chemical pre-treatment and primer, and a top coat. Each performs an important role in providing designers with a high quality, aesthetic, cost competitive and corrosion-resistant material. The backbone of the system is sheet steel, an ideal material for covering large surface areas because of its economy and high strength-toweight ratio. Protection against the demanding Canadian environment is provided by the metallic coating, one of the most effective methods of protecting bare steel from corrosion. Both zinc and aluminum-zinc alloy provide a tough, non-porous coating

The new 10-story “Center for Care and Discovery” building in the University of Chicago Medical Center’s campus is dubbed as the “hospital of the future” for its high-tech design and groundbreaking scientific work. At 1.2 million square feet, it is one of the largest buildings at the campus and has already transformed the skyline of Chicago’s south side.

IntroductionSheet Steel Roong and SidingLightweight Steel FramingIsolate the Steel and Wood ComponentsAvoid Use of Pressure Treated WoodFastenersMany buildings will include wood members in applicationssuch as sill plates, splash boards, strapping, purlins, door orwindow bucks, and posts. In some of these end-uses it is arequirement that the wood be chemically treated (pressuretreated) to extend the service life.Designers and builders need to be aware that changes in theavailable wood perservatives may impact the durability ofany connected steel components or fasteners.Eective January 1, 2004 the Environmental ProtectionAgency (EPA) banned the use of Chromated CopperArsenate (CCA) as a preservative in treated lumber forresidential construction. This was done in an eort to reducethe use of chromate and arsenic thereby mitigating thepotential health and environmental problems. The woodpreservative industry has been switching to alternativewaterborne compounds including Sodium Borate (SBX),Alkaline Copper Quat (ACQ), Copper Azole (CBA-A and CA-B),and Ammoniacal Copper Zinc Arsenate (ACZA).Unfortunately, research has indicated that ACQ, CBA-A, CA-Band ACZA, the new generation copper-based products, aremore corrosive to galvanized steel than the former CCA.Since ACQ is becoming the predominant preservative in use,the discussions in this paper will refer to it exclusively.The purpose of this Fact Sheet is to convey the recommendations of the sheet steel industry for the application of steelproducts with ACQ pressure treated wood.

When the Cincinnati Art Museum embarked on an $11 million renovation, the architects wanted the entrance and main stair to be as inviting as possible. Transparent, fire rated glazing from SAFTI FIRST® was a key component of the design solution. To maximize the vision area in door itself, SuperLite® II-XL 60 in GPX® Builders Series Temperature Rise full-lite doors. In some of the stairwell doors in less prominent locations, SAFTI FIRST® provided SuperLite® X-90 for the vision panels under 100 sq. inches.

CSSBI Position Paper on CGSB Standards for Prefinished Sheet Steel Cladding The National Building Code of Canada 2010 includes references to two documents published by the Canadian General Standards Board (CGSB) dealing with prefinished sheet steel cladding. These documents are: • CAN/CGSB-93.3–M91 Prefinished Galvanized and Aluminum-Zinc Alloy Steel Sheet for Residential Use • CAN/CGSB-93.4–92 Galvanized Steel and Aluminum-Zinc Alloy Coated Steel Siding, Soffits and Fascia, Prefinished, Residential It is important to realize that there are no sheet steel products currently manufactured in Canada that meet the requirements contained in these CGSB standards. 

PREFACE One of the objectives of the Canadian Sheet Steel Building Institute is the development of product standards to promote safety and sound construction practices. This Standard is intended to assist specifiers, designers, buyers, manufacturers, and erectors of sheet steel cladding by providing information which can be adopted by reference where desired. The requirements contained herein are in accordance with sound engineering principles, augmented by experience. They include recommended minimum requirements for such factors as grade of steel, thickness, metallic coating designation, loading and deflections, as well as design, fabrication and erection in general. While the material is believed to be technically correct and in accordance with recognized practice at the time of publication it does not obviate the need to determine its suitability for a given situation. Neither the Canadian Sheet Steel Building Institute nor its members warrant or assume liability for the suitability of the material for any general or particular application. 

PREFACE One of the objectives of the Canadian Sheet Steel Building Institute is the development of product standards to promote safety and sound construction practices. This Standard is intended to assist specifiers, designers, buyers, manufacturers, and erectors of sheet steel cladding by providing information which can be adopted by reference where desired. The requirements contained herein are in accordance with sound engineering principles, augmented by experience. They include recommended minimum requirements for such factors as grade of steel, thickness, metallic coating designation, loading and deflections, as well as design, fabrication and erection in general. While the material is believed to be technically correct and in accordance with recognized practice at the time of publication it does not obviate the need to determine its suitability for a given situation. Neither the Canadian Sheet Steel Building Institute nor its members warrant or assume liability for the suitability of the material for any general or particular application. 

PREFACE One of the objectives of the Canadian Sheet Steel Building Institute is the development of product standards to promote safety and sound construction practices. This Standard is intended to assist specifiers, designers, buyers, manufacturers, and erectors of sheet steel cladding by providing information which can be adopted by reference where desired. This Standard replaces the previous edition dated November 2015. The requirements contained herein are in accordance with sound engineering principles, augmented by experience. They include recommended minimum requirements for such factors as grade of steel, thickness, metallic coating designation, loading and deflections, as well as design, fabrication and erection in general. While the material is believed to be technically correct and in accordance with recognized practice at the time of publication it does not obviate the need to determine its suitability for a given situation. Neither the Canadian Sheet Steel Building Institute nor its members warrant or assume liability for the suitability of the material for any general or particular application.

SuperLite® II-XLM 120 clear butt-glazed walls with 9 ft. GPX® Builders Series 90 minute Temperature Rise doors creates a light-filled, transparent 2-hour stairwell that is on-brand with Waste Management’s new Houston Headquarters.

Introduction Prefinished sheet steel building products, such as wall and roof cladding, liner sheet, flashing, and associated items, have experienced an enviable growth record during the past twenty years or so. Coil coated prefinished sheet steel in a variety of colours and paint systems has greatly enhanced the appearance of thousands of industrial, commercial, institutional, recreational, residential and farm buildings, providing an economical, durable and attractive alternative to traditional materials. As with all materials, a little care and maintenance pays off handsomely in terms of longevity and repair costs. The recommendations which follow have been learned at first hand and represent the collective industry experience with thin-film paint systems applied to metallic coated sheet steel by the coil coating process. In this publication the term “thin-film paint system” refers to a modified silicone polyester or a fluorocarbon type having a coating thickness about 25µm. When the guidelines listed below have been observed, thin-film paint systems have been used successfully for all types of environments other than severe industrial atmospheres which require special consideration. The guidelines are not intended for barrier coatings, laminates, and new formulations which have different characteristics than the thin-film paint systems on which these guidelines are predicated. 

The David Eccles School of Business on the University of Utah campus features a 28- x 18-ft 2 hour interior glass wall with a 90 minute full-vision door in an exit enclosure/stairwell. The architects selected fire rated glass to meet fire rating requirements while providing maximum visibility and natural daylighting in the space. The project’s specifications also required the fire rated glass to have the same optical clarity as the adjacent non-rated glass systems.

The new San Francisco Public Utilities Commission Headquarters combines maximum daylighting and fire safety with a multi-story, fire rated glass stairwell from SAFTI FIRST. Dubbed as the "greenest building in North America," this Class A LEED Platinum office building features a transparent, 2-hour fire rated stairwell, situated prominently near the main entrance. SAFTI FIRST supplied SuperLite II-XL 120 in GPX Architectural Series Wall Framing and SuperLite II-XL 90 in GPX Builders Series Temperature Rise Door starting from the lobby all the way to the topmost floor.

This new 120,000 square foot, state-of-the-art convening center features a 1,000-seat auditorium that is large enough to host the entire MBA class. The glass atrium floods the multi-purpose lobby with natural light, as well as provides a visual connection between the interior of the building and the outdoor environment. To maximize transparency, SAFTI FIRST® met with the architects during the design phase to create a large, 2-hour, glass wall that separates the lobby from the auditorium while providing a visual connection between them. Since this 2-hour glass wall also serves as the entrance to the auditorium, deciding on a 90-minute door system was of upmost important. SAFTI FIRST®’s in-house engineering department provided design assistance, system details, engineering calculations and support from the planning phase all the way to the submittal process.