NBS Source
I'm a manufacturer

Application

Maintains water flow in gutters and drains pipes.

Description

The Raychem self-regulating snow melting system maintains water flow in gutters and drains pipes and provides a path whereby melting ice and snow can drain safely off the roof, along the gutter and down the drain pipe.


System components:

  • Ambient and moisture sensors.
  • Fixing bracket.
  • Control unit.
  • Residual current device (RCD 30 mA) circuit-breaker (C type).
  • Connection RayClic CE-02.
  • Heating cable.
  • End seal.


Features and benefits:

  • The self-regulating cable can be closely spaced in gutters without the risk for overheating or burn-outs. There is a cable for each type of roof material.
  • The system saves energy by automatically increasing its heat output in icy water and decreasing its output in dry air. The smart EMDR-10 control unit only switches the heating cable on when necessary, after the detection of both low temperature and moisture.
  • 25 year cable life expectancy.


General information

Warranty description

Five year

Uniclass

Ss_60_40_90_28 Electrical resistance trace heating systemsPrimary

CAWS

S90/565 Trace heating tape for pipelines

Specification data - Electrical resistance trace heating systems

Application

Freeze protection.

Heat emitters

GM-2X.

Guidance for specification option:

With modified polyolefin jacket. 36 W/m in iced water and 18 W/m in air at 0°C.

GM-2XT.

Guidance for specification option:

With fluoropolymer jacket for use on asphalt, bitumen, roofing felt etc. 36 W/m in iced water and 18 W/m in air at 0°C.

Manufacturer guidance

Cable length:

  • The cable length is determined by the drainpipe length plus 1 m per connection and 1 m in the soil (frost line).
  • The heating cable should be installed in a straight line in the gutter.
  • The cable lengths should be adjusted according to the geographical situation and the gutters.
  • More than one cable should be laid in wide valley, parapet or box gutters.


Electrical protection:

  • The total length of heating cable determines the number and size of the fuses.
  • Residual current device (RCD): 30 mA required, maximum 500 m heating cable per RCD.
  • Installation according to local regulations uses C type circuit breakers.
  • The power connections must be carried out by an approved electrical installer.
  • Consult technical literature for further details.


Controls

SBS-03-EV.

Guidance for specification option:

Control Panel for up to three heating circuits. 380 x 600 x 210 mm.

SBS-06-EV.

Guidance for specification option:

Control Panel for up to six heating circuits. 380 x 600 x 210 mm.

SBS-09-EV.

Guidance for specification option:

Control Panel for up to nine heating circuits. 600 x 600 x 210 mm.

SBS-12-EV.

Guidance for specification option:

Control panel for up to 12 heating circuits. 760 x 760 x 210 mm.

Manufacturer guidance

Control panel:

Steel plate housing, wall-mounted version, equipped with mains isolator, RCD/CB combination(s), indicators for `Operation and Fault‘, inlet and outlet terminals. Completely assembled, wired and inspected. Cable guides in base of housing An EMDR-10 control unit is installed in each switch cabinet.


  • Finish: Structural paint, RAL 7035, light grey.
  • Ingress protection: IP 54.
  • Ambient temperatures: 5–35°C.
  • Cable inserts: Metal plate in base of housing with metric breakout apertures.
  • Mains power connection: three-phase to 400 V/ 230 V, 50 Hz, with N and PE.
  • Location: Interior.


- Customer fuse protection:

  • SBS-03-EV: 3 x 32 A NH-00. Three pin mains isolator switch, 32 A.
  • SBS-06-EV: 3 x 40 A NH-00. Three pin mains isolator switch, 63 A.
  • SBS-09-EV: 3 x 63 A NH-00. Three pin mains isolator switch, 63 A.
  • SBS-12-EV: 3 x 80 A NH-00. Three pin mains isolator switch, 100 A.

Unit

EMDR-10.

Guidance for specification option:

Smart control unit.

  • With temperature (PTC [FL 103]) and moisture sensor (PTC).
  • ser-friendly control.
  • Saves up to 80% energy.
  • Maximum switching capacity 10 A (otherwise switching by contactor).
  • Potential free alarm for sensor break age, sensor short and power loss.
  • Supply voltage: 230 VAC/ 50 Hz.
  • Power consumption: 4 VA (maximum).
  • Maximum switching capacity: 10(4) A/ 230 VAC, SPST, potential 230 VAC.
  • Alarm relay: 2(1)A/ 230 VAC, SPDT, potential-free.
  • Mounting: DIN rail according to DIN EN 50022-35.
  • Low voltage directive EN 60730. EMC EN 50081-1 (emission) and EN 50082-1 (immunity).
  • Ingress protection: IP 20.
  • Housing material: Noryl (self-extinguishing according to UL 94 V-0).

HTS-D.

Guidance for specification option:

Standard thermostat.

  • Two independent switching points.
  • Maximum switching current: 16 A, 250 V AC.
  • Temperature adjustment range: -20°C to +25°C.
  • Ingress protection: IP 65.
  • Temperature setting under the housing cover.
  • Outdoor installation.
  • Economical for circuit lengths up to 30 m.


Connectors

CCE-03-CR.

Guidance for specification option:

Cold lead connection and end seal kit for GM-2X only.

CCE-04-CT.

Guidance for specification option:

Cold lead connection and end seal kit for GM-2XT only.

RayClic-CE-02.

Guidance for specification option:

Power connection with 1.5 m power cable, end seal and support bracket. IP68.

RayClic-PS-02.

Guidance for specification option:

Powered splice, connection for two cables with 1.5 m power cable. Supplied with two end seals and support bracket. IP68.

RayClic-PT-02.

Guidance for specification option:

Power T-connection with 1.5 m power cable for three cable connection. Supplied with three end seals and support bracket. IP68.

Show more

Similar products from nVent Thermal Management

Flow Maintenance of Greasy Waste Pipes

Flow Maintenance of Greasy Waste Pipes

Hot Water Maintenance Controller HWAT ECO v5

Hot Water Maintenance Controller HWAT ECO v5

Pipe Freeze Protection

Pipe Freeze Protection

© 2024 NBS Enterprises Ltd. All rights reserved.