NBS Source
List your products

Ronacrete Ltd

Specialist construction products

+44 (0)1279 638700 www.ronacrete.co.uk

Sort by:

Showing 1-36 of 44

Monoprufe WP Elastic

Monoprufe WP Elastic is a high performance cold applied polymer cement waterproofing membrane. Monoprufe WP Elastic is used in basements, planters and on balconies and terraces to exclude water. Monoprufe WP Elastic is sufficiently elastic to bridge minor dynamic cracks. Monoprufe WP Elastic is a two component blend of polymers, cements, graded fillers and chemical binders. Monoprufe WP Elastic is mixed on site to produce a roller or slurry brush applied thin liquid membrane. Monoprufe WP Elastic must not be used as a wearing surface, it may be covered with screeds, renders, tiles, resilient flooring etc.

RonaBond Anti-Carbonation Coating WB

RonaBond Anti-Carbonation Coating WB is a smooth creamy water based acrylic coating. It is used as a protective and decorative coating for new, maintenance and refurbishment work and can be applied to most traditional building surfaces including concrete, repair mortar, render and masonry after preparation. It provides a weather resistant surface which resists the ingress of CO2 and allows the substrate to breathe

RonaBond Bedding Mortar

RonaBond Bedding Mortar is used to bond brick slips, copings and other components to concrete and building surfaces. The cured mortar has high physical strength, is waterproof and frost proof and will not break down through frost action.

RonaBond Concrete Cover 150

RonaBond Concrete Cover 150 is a coating designed to improve equivalent concrete cover to reinforcement. A 4mm layer provides 150mm equivalent concrete cover providing corrosion protection to steel reinforcement thus extending the life of the concrete. RonaBond Concrete Cover 150 is supplied as a pre packed material comprising liquid and powder. It is mixed to form a slurry which is applied by brush or roller at a thickness of approximately 0.5mm per coat on a vertical surface. The cured coating can be left as the finished surface or overcoated with a pigmented anti-carbonation coating such as RonaBond Crack Bridging Anti-Carbonation Coating WB or RonaBond Anti-Carbonation Coating WB.

RonaBond Concrete Repair Mortar

RonaBond Concrete Repair Mortar is a prepacked, ready to use mortar for concrete repair and is used with Ronacrete Standard Primer which gives monolithic adhesion to all correctly prepared surfaces. RonaBond Concrete Repair Mortar is used to repair and replace concrete damaged as a result of spalling through reinforcement corrosion, freeze/thaw cycling, impact or other damage.

RonaBond Crack Bridging Anti Carbonation Coating WB

RonaBond Crack Bridging Anti-Carbonation Coating WB is a façade coating formulated on a water based acryl siloxane. It is used as a waterproof decorative coating and can be applied to most traditional building surfaces after suitable preparation. The addition of siloxane improves shedding of pollutants from the surface and resistance to migration residues from the substrate. RonaBond Crack Bridging Anti-Carbonation Coating WB is a high build elastomeric, waterproof and carbonation resistant coating. It protects facades against water ingress while allowing diffusion of normal levels of moisture vapour from the background. When applied to reinforced concrete it provides excellent protection against corrosion of reinforcement.

RonaBond EasySkim FC

RonaBond EasySkim FC is a pre-packed fairing coat mortar which is applied as a skim coat in thicknesses up to 3mm to provide a smooth, hard finish to damaged, blemished and repaired concrete surfaces. RonaBond EasySkim FC is used as a levelling mortar prior to the application of protective coatings or paints. The material is supplied in pre-blended form.

RonaBond Flowable Micro Concrete

RonaBond Flowable Micro Concrete is a repair concrete used for reinstatement of structural elements such as columns and beams. RonaBond Flowable Micro Concrete is designed for pumped or poured application to watertight shutters when hand application of mortars is impractical or undesirable. RonaBond Flowable Micro Concrete is shrinkage compensated and provides high ultimate strengths.

RonaBond H25

RonaBond HB25 is a prepacked mortar used for repairing concrete on vertical and overhead surfaces where ease of application is as important as high strength. It can be applied in relatively thick section to walls and soffits and, depending on the nature of the repair, in layers up to 75mm deep in pocket repairs. RonaBond HB25 is supplied prepacked requiring only the addition of water. The cured mortar bonds well to concrete, steel and other building surfaces. It offers long term performance and protection to structures.

RonaBond HB40

RonaBond HB40 mortar is used for repairing concrete on vertical and overhead surfaces where ease of application is as important as strength. RonaBond HB40 can be applied in relatively thick section to walls and soffits and, depending on the nature of the repair, in layers up to 75mm depending on size and orientation.

RonaBond MCI

RonaBond MCI is a surface applied corrosion inhibitor. It is designed to migrate through normal and dense concrete structures and seek out the steel reinforcement bars in concrete. RonaBond MCI will migrate a considerable distance through concrete to provide protection. RonaBond MCI will stop further corrosion of reinforcing metals and extend the service life of the structure.

RonaDeck Eco Tree Pit

RonaDeck Eco Tree Pit is a resin bound natural aggregate finish surround for planted trees in public and private areas. Surrounding the tree in a solid yet semi-flexible construction allows the tree to grow, prevents a build up of litter and removes a storage or hiding place for hazardous items such as syringes and needles. Dogs are also less likely to foul in such areas. Its porosity allows water to flow through a 6-10mm aggregate system at the rate of >850 litres/m2/minute. The flow rate may be reduced when using a smaller or more angular aggregate.

RonaDeck EcoAgg UV

RonaDeck EcoAgg UV is a resin bound aggregate surface for pedestrian traffic. RonaDeck EcoAgg UV surfaces are decorative and functional, seamless and slightly flexible. The open matrix allows water to drain through to the base, eliminating water ponding and allowing water to drain to planted areas or land drains. The system is designed to be SuDS compliant reducing the impact of development on flood risk and allowing water to flow into water courses or water harvesting systems. Edgings created from brick, stone, timber or steel should be installed to retain and protect the resin bound surfacing.

RonaDeck EcoPath UV

RonaDeck EcoPath UV is a resin bound aggregate surface for pedestrian traffic. RonaDeck EcoPath UV surfaces are decorative and functional, seamless and slightly flexible. The open matrix allows water to drain through to the base, eliminating water ponding and allowing water to drain to planted areas or land drains. The system is designed to be SuDS compliant reducing the impact of development on flood risk and allowing water to flow into water courses. Edgings created from brick, stone, timber or steel should be installed to retain and protect the resin bound surfacing. RonaDeck EcoPath UV is typically applied to compacted Type 3 aggregate to provide a thin alternative to asphalt or concrete. RonaDeck EcoPath UV is designed for light foot traffic only.

RonaDeck Resin Bonded Surfacing

RonaDeck Resin Bonded Surfacing is a resin bonded aggregate surfacing system for paths, car parks, drives, ramps, highways etc. RonaDeck Resin Bonded Surfacing produces a surface with the appearance of natural aggregate or stone but with aggregate which is firmly bonded to the surface. It is designed for use on concrete, asphalt, steel and timber surfaces to provide some or all of the following: Decoration High friction surfacing Colour coding Compliance with Disability Discrimination Act Minimal maintenance An alternative to loose aggregate and stone surfacing RonaDeck Resin Bonded Surfacing provides surfaces for all types of traffic from paths to busy highways and provides excellent traction in wet and dry conditions.

RonaDeck Resin Bound and Bonded Surfacing

The RonaDeck Resin Bound and Resin Bonded Surfacing range of products provide highly decorative and functional systems for exterior pavement surfacing.

RonaDeck Resin Bound Surfacing

RonaDeck Resin Bound Surfacing is a resin bound aggregate surface for pedestrian and vehicular traffic. RonaDeck Resin Bound surfaces are decorative and functional, seamless and slightly flexible. The open matrix allows water to drain through to the base, eliminating water ponding and allowing water to drain to planted areas or land drains. The surfacing may be applied to SuDS compliant bases and sub-bases, reducing the impact of urban development on flood risk and allowing water to flow into water courses. Edgings created from brick, stone, timber or steel should be installed to retain and protect the resin bound surfacing.

RonaDeck Rubber Granule Tree Pit

RonaDeck UV Rubber Granule Tree Pit is a resin bound rubber granule tree pit surfacing for trees in hard landscaped areas. RonaDeck UV Rubber Granule Tree Pit surrounds trees in a solid yet porous and flexible construction, allowing drainage of rainwater to roots and unlike grilles presenting no voids for litter, or hiding of syringes and needles. The RonaDeck UV Rubber Granule Tree Pit comprises a two layer system of resin bound rubber granules. The thicker base layer is composed of black recycled 2-6mm granules bound in UV stable polyurethane resin and the topping layer of 1-4mm coloured granules is bound in the same resin. The design of this resin bound tree pit system provides a surface which is attractive, highly porous and able to receive light foot traffic.

RonaDeck Wet Pour Rubber Granule Surfacing

RonaDeck UV Wet Pour Rubber Granule Surfacing is a resin bound rubber granule surfacing for pedestrian traffic. It is used to create flexible seamless safety surfaces which absorb sound and impact. RonaDeck UV Wet Pour Rubber Granule Shockpad is a base layer for absorbing impact below and around play equipment. The system must be laid onto a sound stable and solid base; concrete or no fines concrete is the preferred substrate, the system may be applied to asphalt concrete but there is a risk of migratory staining from the bitumen binder. Applications exceeding 40mm depth may be laid on compacted MoT Type 3 aggregate. RonaDeck UV Wet Pour Rubber Granule Surfacing is suitable for applications in areas such as playgrounds and golfing environments.

Ronafix for Screeds

Ronafix screeds are site batched screeding mortars and fine concretes. The mix design for each is Ronafix admixture, cement, medium grade sharp sand, aggregate as determined by the mix design, plus water. The components are measured by weight or by volume on site and mixed to form the screed. They are used with a primer of Ronafix and cement which achieves monolithic adhesion to correctly prepared concrete or screeds. Ronafix screeds are used to lay new screeds and toppings as thin as 6mm bonded or 35mm unbonded or floating. The cured mortar bonds securely to suitably prepared surfaces and is water resistant.

Ronafix Pre-packed Floating Screed 35mm+

Ronafix Pre-packed Floating Screed 35mm+ is supplied as a pre-packed, two component, ready to use mortar for laying floor screeds on insulation boards. Ronafix Pre-packed Floating Screed 35mm+ is supplied complete with all the correct dry components in a bag and a bottle of polymer gauging liquid.   Ronafix Pre-packed Floating Screed 35mm+ is used to lay minimum 35mm floating screeds for residential applications. Screed thickness should be increased for medium to heavy duty use, The screed is resistant to water, frost, and medium to heavy wear when covered with a suitable flooring.

Ronafix Pre-packed Screed 6-50mm

50mm is supplied as a pre-packed, two component, ready to use mortar for laying floor screeds. Ronafix Pre-packed Screed 6-50mm is supplied complete with all the correct dry components in a bag and a bottle of polymer gauging liquid. Ronacrete Standard Primer two part polymer cement bonding agent is required for bonded screed applications. Ronafix Pre-packed Screed 6-50mm is used to lay new screeds and toppings as thin as 6mm for light duty bonded and 35mm unbonded or floating applications. Screed thickness should be increased for medium to heavy duty use, Excellent adhesion can be achieved to suitably prepared surfaces and the screed is resistant to water, frost, and medium to heavy wear.

Showing 1-36 of 44