"concrete blocks"

Soaring to a height of 1,776 feet (540-meters), the 2.6-million-squarefoot (242,000-square-meter) skyscraper known as One World Trade Center in the lower Manhattan district of New York City is a marvel of design and engineering. Construction of the building, previously called the Freedom Tower, began in April 2006 and at the time was the tallest building in the United States.The Challenge Sustainable design was a central theme to One World Trade Center’s development, with the Port Authority of New York/ New Jersey imposing a strict requirement for the replacement of Portland cement with recycled materials. In addition, extremely high performance concrete was necessary to meet the compressive strength requirements of the steel and concrete structural columns, which ranged from 14,000 psi (97 MPa) to 12,000 psi (83 MPa) for the lower 40 floors and 10,000 psi (69 MPa) to 8,600 psi (59 MPa) for the upper floors. The 12,000 psi (83 MPa) concrete phase of the project was the most challenging, with the engineers, owners and contractors all having their own requirements and specifications.The ResultsThrough Master Builders Solutions‘ Green Sense Concrete mixture optimization service, Eastern Concrete Materials was able to proportion an EF Technology® concrete mixture with 71% cement replacement. The mixture replaced Portland cement with the recycled materials, non-cementitious fillers and specialized admixtures to exceed all the performance targets specified by the One World Trade Center project stakeholders. This EF Technology mixture was used for the 38,000 yd3 (29,000 m3) of concrete needed for the columns through the first 40 floors. To quantify the environmental impact of sustainable concrete for the structure, an Eco-Efficiency Analysis was conducted, using a methodology validated by NSF International, to compare the specialized EF Technology mixture to a reference mixture. Some practical equivalents for these savings are: Water savings equal to 1,177,329 half-liter bottles of waterReduced carbon footprint equal to 1,835,494 gallons of gasolineFossil fuel savings equal to 29,872 barrels of oil

A case study of the use of Airtight White Intelligent Airtight Liquid Vapor Control

Start at the foundation where the loads imposed by a steel frame are up to 50% less than those of a concrete alternative. There is evidence in the field and through third-party case studies and comparative cost studies that steel building systems offer significant cost benefits over competitive building materials when the total cost of construction is considered.

Prairie Hills Junior High School's south-facing elevation features a glazed aluminum curtain wall that incorporates PPG Solarblue and PPG Solarban 60 glazing. Parts of the curtain wall had to meet a two-hour rating because it was adjacent to a two-hour block wall through the building's interior. SAFTI FIRST® supplied SuperLite® II-XL 120 IGU in GPX® Curtain Wall Framing in order to meet ASTM E-119/NFPA 251/UL263 requirements.

Traditional parking garage designs used to have opaque fire rated building materials like concrete, masonry and drywall which made these spaces dark, cold and uninviting. That all changed, thanks to the emergence of new technology, clear, fire resistive glazing tested to ULC/CAN S101 up to 2 hours that are available in large sizes and low-iron glass make-ups with high visible light transmission for superior clarity and color neutrality.

Codes required fire wall separations between parking garages and businesses, markets, homes and other uses. Architects can replace entire walls with glass to open up buildings like never before. For example, SuperLite® II-XL in GPX® Architectural Series Framing by SAFTI FIRST® is a USA-made fire resistive transparent wall system that blocks radiant heat and meets the same stringent ASTM E-119/ UL 263/ NFPA 251 code requirements that any opaque fire rated wall must meet.

An old block of apartments in Gt. Yarmouth getting a low carbon Retrofit for a higher, cleaner living standard and reduced energy bills. Passive Purple has been used externally on this huge scale block of apartments. with no margin for error and tricky details throughout, a liquid applied airtight membrane was the only way going forward. The building was being insulated externally and getting a whole new façade from render to aluminium panels. With the residents still inhabiting the building this had to be done quickly and easily with maximum results. Being a liquid applied airtight membrane, any cracks, gaps, and service penetration leaks in the existing building fabric quickly became thing of the past. That and the hundreds of Panel brackets being installed to support the new façade going on, this Retrofit had multiple penetrations and tricky details. Making good of the building fabric and awkward brackets with a near on impenetrable adhesion, Passive Purple made fast work of this great conversion, impossible for any other method. Being in liquid state on application, Passive Purple can be applied onto most/any surface (See data sheets for more information) and will find its way into all the unseeable tiny gaps and cracks all buildings will undoubtably have. Like this old pebble dashed façade, any rough, uneven and awkward areas are no longer an issue, our products simply flow into these areas. We also have the fibre reinforced Passive Purple brush, used on this job to prepare the brackets by filling the larger gaps between that of the bracket and the existing wall and also the large penetrating bolts. A huge win and demonstration of the power of liquid products by Intelligent Membranes.